Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD2004ECONOLINE E150, VAN CARGO, 4.6 WREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 46 (ENGINE CONTROLS - REMOVAL, OVERHAUL & INSTALLATION)TORQUE SPECIFICATIONS
2004 Ford Econoline E150, Van Cargo, 4.6 W
Torque Specifications
2004 Ford Econoline E150, Van Cargo, 4.6 WSECTION Torque Specifications
WARNING: This page is about a different car, the 2002 Mercury Grand Marquis, 2002 Lincoln Town Car, and 2002 Ford Crown Victoria. However, it is still accessible from the selected car via links, so may be relevant.
TORQUE SPECIFICATIONS
| Application | Ft. Lbs. (N.m) | |||
|---|---|---|---|---|
| Crash Bracket Bolt | 18 (25) | |||
| Cylinder Head Temperature Sensor | 20 (27) | |||
| EGR Tube Nut | 30 (40) | |||
| EGR Valve Bolt | 14-16 (18-22) | |||
| Engine Coolant Temperature Sensor | 15 (20) | |||
| Exhaust-To-Convertor Nut | 21 (29) | |||
| Fuel Tank Support Strap Nut | 26 (35) | |||
| Heated Oxygen Sensor | 30 (41) | |||
| Intake Manifold Bolt | 18 (25) | |||
| Spark Plug | 11 (15) | |||
| Thermostat Housing Bolt | 18 (25) | |||
| INCH Lbs. (N.m) | ||||
| Accelerator Cable Bracket Bolt | 53 (6) | |||
| Alternator-To-Intake Manifold Bracket Bolt | 89 (10) | |||
| Camshaft Position Sensor Bolt | 89 (10) | |||
| Crankshaft Position Sensor Bolt | 89 (10) | |||
| Engine Cover Bolt | 89 (10) | |||
| EVAP Canister Fastener | 53 (6) | |||
| EVAP Purge Valve Nut | 68-72 (7.6-10.4) | |||
| Fuel Filler Screw | 27-35 (3-4) | |||
| Fuel Injection Supply Manifold | 89 (10) | |||
| Fuel Pump Module Bolt | 80-107 (9-12) | |||
| Generator Harness Nut | 89 (10) | |||
| Idle Air Control Valve Bolt | 89 (10) | |||
| PCM Cover Nut | 53 (6) | |||
| PCM Harness Bolt | 53 (6) | |||
| Throttle Body Bolt | ||||
| Step 1 | 89 (10) | |||
| Step 2 | (1) | |||
| Throttle Position Sensor Bolt | 27 (3) | |||
| Upper Intake Manifold Bolt | 89 (10) | |||
|
||||
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.