2000 Ford ZX2 AutomaticFACTORY OEM SERVICE PROCEDURE

Specifications Index

ESCORT & ZX2 SPECIFICATIONS INDEX

System Specification/Procedure
Air Conditioning
Service SPECIFICATIONS
Torque TORQUE SPECIFICATIONS
Axle Nut/Hub Nut 174-235 Ft. Lbs. (235-319 N.m)
Brakes
Bleeding Sequence BLEEDING BRAKE SYSTEM
Disc Brakes DISC BRAKE SPECIFICATIONS
Drum Brakes DRUM BRAKE SPECIFICATIONS
Torque TORQUE SPECIFICATIONS
Charging
Generator ON-VEHICLE TESTING
Torque TORQUE SPECIFICATIONS
Drive Belts
Adjustment BELT ADJUSTMENT
Belt Routing DRIVE BELT ROUTING
Engine Cooling
General Service Specifications COOLING SYSTEM SPECIFICATIONS
Radiator Cap Pressure 16 Lbs.
Thermostat R & I
DOHC N/A
SOHC THERMOSTAT
Water Pump
DOHC WATER PUMP
SOHC WATER PUMP
Engine Mechanical
DOHC
Compression ENGINE COMPRESSION
Oil Pressure 54-80 psi (3.8-5.6 kg/cm2 ) at 4000 RPM
Overhaul ENGINE SPECIFICATIONS
Torque TORQUE SPECIFICATIONS
SOHC
Compression ENGINE COMPRESSION
Oil Pressure 35-65 psi (2.5-4.6 kg/cm2 ) at 2000 RPM
Overhaul ENGINE SPECIFICATIONS
Torque TORQUE SPECIFICATIONS
Fluid Specifications See FLUIDS under MAINTENANCE tab.From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button
Flywheel/Flex Plate Torque
DOHC 75-85 Ft. Lbs (107-115 N.m)
SOHC 54-67 Ft. Lbs. (73-91 N.m)
Fuel System
Fuel Filter Location Located in rear of engine compartment, mounted in clamp.
DOHC
Pressure Release Procedure FUEL PRESSURE RELEASE & FUEL LINE CONNECTIONS
Pressure Specification 30-45 psi (207-310 kPa)
Fuel Pressure Test Procedure FUEL PRESSURE
SOHC
Pressure Release Procedure FUEL PRESSURE RELEASE & FUEL LINE CONNECTIONS
Pressure Specification FUEL PRESSURE -- CARS
Fuel Pressure Test Procedure FUEL PRESSURE
Fuel Filter R & I REMOVAL & INSTALLATION .
Ignition
Firing Order & Cylinder Identification FIRING ORDER & CYLINDER IDENTIFICATION
Ignition Wires (Resistance) HIGH TENSION WIRE RESISTANCE
Ignition Wires (Routing) FIRING ORDER & TIMING MARKS
Spark Plugs
DOHC
Type Motorcraft AZFS-32FE
Gap .048-.052 In. (1.20-1.32 mm)
Torque 10-12 Ft. Lbs. (13-17 N.m)
SOHC
Type Motorcraft AGSF-34EE
Gap .052-.056 In. (1.30-1.40 mm)
Torque 7-15 (10-20 N.m)
Starting
Starter STARTER MOTOR SPECIFICATIONS
Torque TORQUE SPECIFICATIONS
Wheel Alignment
Adjustment Specifications WHEEL ALIGNMENT SPECIFICATIONS
Torque TORQUE SPECIFICATIONS
Wheel & Tire
Lug Nut Torque 74-100 Ft. Lbs. (100-136 N.m)
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.

Rather have a pro handle this?

A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.

Comes to youSame-day available12-month warranty
Get a Free Quote

No obligation. See pricing before you book.