Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
1999 Ford Contour SVTFACTORY OEM SERVICE PROCEDURE
Parameter Identification (PID) Definitions
ANTI-LOCK BRAKE SYSTEM MODULE PID INDEX
| PID | Description | Expected Value | ||
|---|---|---|---|---|
| CCNTABS | Number Of Continuous DTC | One Count Per Bit | ||
| BOO_ABS | Brake Pedal Position Switch Input | ON, OFF | ||
| PMP_MTR | ABS Pump Motor | (1) | ||
| VLV_CTR | ABS Valve Control Relay | (1) | ||
| ABSRR_O | Right Rear ABS Outlet Valve | (1) | ||
| ABSLR_O | Left Rear ABS Outlet Valve | (1) | ||
| ABSRF_O | Right Front ABS Outlet Valve | (1) | ||
| ABSLF_O | Left Front ABS Outlet Valve | (1) | ||
| ABSRF_I | Right Front ABS Inlet Valve | (1) | ||
| ABSLF_I | Left Front ABS Inlet Valve | (1) | ||
| ABSRR_I | Right Rear ABS Inlet Valve | (1) | ||
| ABSLR_I | Left Rear ABS Inlet Valve | (1) | ||
| LF_WSPD | Left Front Wheel Speed Signal | 0-255 KPH | ||
| RF_WSPD | Right Front Wheel Speed Signal | 0-255 KPH | ||
| LR_WSPD | Left Rear Wheel Speed Signal | 0-255 KPH | ||
| RR_WSPD | Right Rear Wheel Speed Signal | 0-255 KPH | ||
|
||||
POWERTRAIN CONTROL MODULE PID INDEX
| PID | Description | Expected Value |
|---|---|---|
| CCNTABS | Number Of Continuous DTC | One Count Per Bit |
| NUMKEYS | Number Of Ignition Keys Programmed | 0 To 8 |
| M_KEY | Is This A Programmed Key | YES, NO |
| ENABL_S | Vehicle Starting Status | ENABLED, DISABLED |
| MIN#KEYS | Minimum Number Of Programmed Keys Required To Start Vehicle | 2 To 8 |
| ANTISCAN | 20-Second Time-Out After Attempting To Use Unprogrammed Key | ACTIVE, NOTACT |
| SPARE_KEY | Can You Add Spare Keys With 2 Programmed Keys | YES, NO |
| SERV_MOD | Is This A Repair Module | YES, NO |
RESTRAINT CONTROL MODULE PID INDEX
| PID | Description | Expected Value |
|---|---|---|
| CCNT | Number Of Continuous DTCs On Speed Control Servo | One Count Per Bit |
| VBATT | Battery Voltage At RCM | 9-16 Volts |
| D_ABAGR | Driver's Air Bag Module Resistance | 1.7-4.1 Ohms |
| P_ABAGR | Passenger's Air Bag Module Resistance | 1.7-3.2 Ohms |
| BRACKET | Bracket Ground Resistance | Less Than 100 Ohms |
| VID NO1 | Programmed Vehicle ID Pin 10 | IGNITION |
| VID NO2 | Programmed Vehicle ID Pin 13 | IGNITION |
| VID NO3 | Programmed Vehicle ID Pin 14 | NO CONNECTION |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
