Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD1993E 350 VAN V8-7.3L DSLREPAIR AND DIAGNOSISPOWERTRAIN MANAGEMENTCOMPUTERS AND CONTROL SYSTEMSTECHNICAL SERVICE BULLETINS
1993 Ford E 350 Van V8-7.3L DSL
Computers and Control Systems: Technical Service Bulletins
1993 Ford E 350 Van V8-7.3L DSLSECTION Technical Service Bulletins
- Customer Interest
- By Symptom
- Customer Interest
- Erratic Shifting
- False instrument warning light/gauges
- A/T - Harsh Shifts/Trouble Code 62/TCIL Lamp Flashes
- EEC IV - Self Test Codes and MIL Service Tips
- Overview
- Overview of Three Digit EEC-IV Self-Test Codes
- 1) Technician Not Familiar With Self-Test Code Output
- 2) Inadvertent Erasure of Continuous Memory Self-Test Codes
- 3) Concern Setting Continious Memory Code Isn't Present
- 4) Grounded STO/MIL Circuit
- 5) Engine Running In Hlos
- 6) Misinterpretation of MIL Bulb Check
- 7) MIL Flashes During Self-Test
- 8) Processor KAM Is Erased or Fails
- 9) Damaged Star Tester
- 10) KOEO Processor Ram Test Failed
- 11) Intermittent VSS Fault Detected In Wiggle Mode
- 12) IDM Pulswidth Not Recognized By Processor (EDIS Vehicles)
- 13) Intermittent Ignition System Fault
- 14) Intermittent Open STI Circuit
- 15) Power Lost to EEC Processor
- 16) Other Warning Lamps Mistaken For MIL
- 17) Development Testing /Wrong Processor Released to Production
- Hard Shifting
- Poor performance
- Slipping
- Starting problems
- All Technical Service Bulletins
- A/T - E4OD TCIL Flashing/DTC's 62/628/1728 Stored
- A/T - Harsh Shifts/Trouble Code 62/TCIL Lamp Flashes
- EEC IV - Self Test Codes and MIL Service Tips
- Overview
- Overview of Three Digit EEC-IV Self-Test Codes
- 1) Technician Not Familiar With Self-Test Code Output
- 2) Inadvertent Erasure of Continuous Memory Self-Test Codes
- 3) Concern Setting Continious Memory Code Isn't Present
- 4) Grounded STO/MIL Circuit
- 5) Engine Running In Hlos
- 6) Misinterpretation of MIL Bulb Check
- 7) MIL Flashes During Self-Test
- 8) Processor KAM Is Erased or Fails
- 9) Damaged Star Tester
- 10) KOEO Processor Ram Test Failed
- 11) Intermittent VSS Fault Detected In Wiggle Mode
- 12) IDM Pulswidth Not Recognized By Processor (EDIS Vehicles)
- 13) Intermittent Ignition System Fault
- 14) Intermittent Open STI Circuit
- 15) Power Lost to EEC Processor
- 16) Other Warning Lamps Mistaken For MIL
- 17) Development Testing /Wrong Processor Released to Production
- A/T - E4OD Harsh/Double Bump On Reverse Engagement
- Engine Control - Cold Temperature Hard Start/No Start
- Heated Exhaust Gas Oxygen Sensor - Application Chart
- A/T - E4OD Shift Concerns/DTC's Set
- A/T - E4OD New Design Transmission Range Sensor
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.