Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD1988BRONCO 4.9 Y, AUTOMATICREPAIR AND DIAGNOSIS (SINGLE PAGE)ENGINE PERFORMANCESYSTEMEEC-IV CEC SYSTEMQUICK TESTHOW TO USE CIRCUIT TESTS
1988 Ford Bronco 4.9 Y, Automatic
How To Use Circuit Tests
1988 Ford Bronco 4.9 Y, AutomaticSECTION How To Use Circuit Tests
- DO NOT perform any CIRCUIT TEST (TEST A1 through TEST D23) unless directed to do so by QUICK TEST. Ensure all non-EEC related faults are corrected. FOLLOW EACH TEST STEP IN ORDER UNTIL FAULT IS FOUND. DO NOT replace any part unless directed to do so. When more than one service code is received, start with the first code displayed.
- DO NOT
measure voltage or resistance at ECA or connect any test light, unless specified. All measurements are made by probing REAR of connector. Isolate both ends of a circuit and turn key off whenever checking for shorts or continuity, unless specified.NOTE: When directed in testing procedure to service or repair TFI ignition system, see MOTORCRAFT TFI-IV IGNITION article in the DISTRIBUTORS & IGNITION SYSTEMS section.
- Disconnect solenoids and switches from harness before measuring continuity, resistance, or applying 12 volts. After each repair, check all component connections and repeat CIRCUIT TEST(S).
- An "open" is defined as any resistance reading greater than 5 ohms. This specification tolerance may be too high for some items in the EEC-IV system. If a resistance approaches 5 ohms, always clean the suspected connector and coat with protective dielectric silicone grease. A "short" is defined as any resistance reading less than 10K ohms to ground, unless specified in CIRCUIT TEST.
- On FUEL CONTROL TESTS C1 and C2, to prevent replacement of good components, be aware that the following non-EEC related areas may also be at fault. These areas include ignition coil, distributor cap and rotor, spark plug wires, fouled spark plugs, CANP problems, EGR valve and gasket, air filter, poor power and ground circuits, fuel pressure, intake and exhaust manifold leaks, engine not at normal operating temperature, and problems with PCV valves or fuel contaminated engine oil.NOTE: Fuel contaminated engine oil may affect some service codes. If this is suspected, remove PCV valve from valve cover and repeat QUICK TEST . If problem is corrected, change engine oil and filter.
- On FUEL CONTROL TESTS C1 and C2, vacuum leaks in non-EEC related areas may also cause code 41 or 91 to be displayed. Check for unmetered air leaks between airflow meter and throttle body, leaking vacuum motors, engine seals, EGR system, PCV system, Canister Purge (CANP) problems, or contaminated HEGO sensor. Code 42 or 92 may be caused by fuel contaminated engine oil, ignition misfire, EGR system, or CANP problems.NOTE: In the following diagnostic charts, circuits and illustrations are supplied courtesy of Ford Motor Co.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.