SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSFORD1985ECONOLINE E350, VAN DISPLAY EXTENDED, 5.8 GREPAIR AND DIAGNOSIS (SINGLE PAGE)SUSPENSIONWHEEL ALIGNMENTWHEEL ALIGNMENT SPECIFICATIONS & PROCEDURESWHEEL ALIGNMENT SPECIFICATIONS
1985 Ford Econoline E350, Van Display Extended, 5.8 G

Wheel Alignment Specifications

1985 Ford Econoline E350, Van Display Extended, 5.8 GSECTION Wheel Alignment Specifications
WHEEL ALIGNMENT SPECIFICATIONS - E150

Axle Gap (Inches) (1) Specification
4 to 4 1/4
Caster (Degrees) 4 1/2 to 6
Camber (Degrees) -3/4 to 3/4
Toe-in (Inches) 1/32
Steering Axis Inclination (Degrees) 7.5
4 1/4 to 4 1/2
Caster (Degrees) 4 to 5 1/2
Camber (Degrees) -1/2 to 1
Toe-in (Inches) 1/32
Steering Axis Inclination (Degrees) 7.5
4 1/2 to 4 3/4
Caster (Degrees) 3 1/4 to 4 1/2
Camber (Degrees) 1/4 to + 1 3/4
Toe-in (Inches) 1/32
Steering Axis Inclination (Degrees) 7.5
4 3/4 to 5
Caster (Degrees) 2 1/2 to 4
Camber (Degrees) 1/2 to 2
Toe-in (Inches) 1/32
Steering Axis Inclination (Degrees) 7.5
5 to 5 1/4
Caster (Degrees) 2 to 3 1/4
Camber (Degrees) + 3/4 to 2 1/2
Toe-in (Inches) 1/32
Steering Axis Inclination (Degrees) 7.5
5 1/4 to 5 1/2
Caster (Degrees) 1 1/2 to 2 3/4
Camber (Degrees) 1 1/4 to 3
Toe-in (Inches) 1/32
Steering Axis Inclination (Degrees) 7.5
5 1/2 to 5 3/4
Caster (Degrees) 1 to 2 1/4
Camber (Degrees) 1 3/4 to 3 1/2
Toe-in (Inches) 1/32
Steering Axis Inclination (Degrees) 7.5
5 3/4 to 6
Caster (Degrees) 1/4 to 1 1/2
Camber (Degrees) 2 1/4 to 4
Toe-in (Inches) 1/32
Steering Axis Inclination (Degrees) 7.5
(1) Axle gap is distance measured from top of axle tube to bottom of spring tower at center front face of jounce stop.
WHEEL ALIGNMENT SPECIFICATIONS - E250/350

Axle Gap (Inches) (1) Specification
3 3/4 to 4
Caster (Degrees) 7 1/2 to 9
Camber (Degrees) -3/4 to 3/4
Toe-in (Inches) 1/32
Steering Axis Inclination (Degrees) 8
4 to 4 1/4
Caster (Degrees) 7 to 8 1/2
Camber (Degrees) -1/2 to 1 1/4
Toe-in (Inches) 1/32
Steering Axis Inclination (Degrees) 8
4 1/4 to 4 1/2
Caster (Degrees) 6 1/4 to 7 3/4
Camber (Degrees) 0 to 1 3/4
Toe-in (Inches) 1/32
Steering Axis Inclination (Degrees) 8
4 1/2 to 4 3/4
Caster (Degrees) 5 1/2 to 7 1/4
Camber (Degrees) 1/2 to 2 1/4
Toe-in (Inches) 1/32
Steering Axis Inclination (Degrees) 8
4 3/4 to 5
Caster (Degrees) 5 to 6 1/4
Camber (Degrees) 1 to 2 3/4
Toe-in (Inches) 1/32
Steering Axis Inclination (Degrees) 8
5 to 5 1/4
Caster (Degrees) 4 1/2 to 5 3/4
Camber (Degrees) 1 1/2 to 3 1/4
Toe-in (Inches) 1/32
Steering Axis Inclination (Degrees) 8
5 1/4 to 5 1/2
Caster (Degrees) 3 3/4 to 5 1/4
Camber (Degrees) 2 to 3 3/4
Toe-in (Inches) 1/32
Steering Axis Inclination (Degrees) 8
(1) Axle gap is distance measured from top of axle tube to bottom of spring tower at center front face of jounce stop.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.