SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSEAGLE1992TALON TSI, FWD, STANDARDREPAIR AND DIAGNOSIS (SINGLE PAGE)ENGINE PERFORMANCESENSOR RANGE CHARTSENGINE CONTROLS - SENSOR OPERATING RANGE CHARTSSENSOR OPERATING SPECIFICATIONS
1992 Eagle Talon TSi, FWD, Standard

Sensor Operating Specifications

1992 Eagle Talon TSi, FWD, StandardSECTION Sensor Operating Specifications
NOTE: Unless stated otherwise in test procedure, perform all voltage tests using a Digital Volt-Ohmmeter (DVOM) with a minimum 10-megohm input impedance.
AIRFLOW SENSOR RESISTANCE (1)

Application Terminals No. Ohms
1.8L & 2.0L Non-Turbo 4 & 6 (2)
2.0L Turbo 6 & 8 (2)
(1) For testing procedure, see I - SYS/COMP TESTS article in the ENGINE PERFORMANCE Section.
(2) Resistance should be approximately 6000 ohms at 32°F (0°C), 2700 ohms at 68°F (20°C) and 400 ohms at 176°F (80°C).
COOLANT TEMPERATURE SENSOR RESISTANCE (1)

Temperature: °F (°C) Ohms
32 (0) 5900
68 (20) 2500
104 (40) 2700
176 (80) 300
(1) For testing procedure, see I - SYS/COMP TESTS article in the ENGINE PERFORMANCE Section.
EGR TEMPERATURE SENSOR RESISTANCE (1)

Temperature: °F (°C) Ohms
122 (50) 6000-8300
212 (100) 1100-1400
(1) For testing procedure, see I - SYS/COMP TESTS article in the ENGINE PERFORMANCE Section.
IDLE SPEED MOTOR POSITION SENSOR RESISTANCE (1.8L) (1)

Terminals No. Ohms
2 & 3 4000-6000
3 & 5 (2) 4000-6000
(1) For testing procedure, see I - SYS/COMP TESTS article in the ENGINE PERFORMANCE Section.
(2) With idle speed control plunger activated.
OXYGEN SENSOR VOLTAGE (1)

Application Volts
1.8L (2) .6-1.0
(1) For testing procedure, see I - SYS/COMP TESTS article in the ENGINE PERFORMANCE Section.
(2) Warm engine until coolant temperature reaches 185-205°F (85-96°C). Measure voltage with engine running at more than 1300 RPM.
THROTTLE POSITION SENSOR RESISTANCE (1)

Terminals No. Ohms
1 & 4 3500-6500
2 & 4 3500-6500
(1) Operate throttle valve slowly from idle position to full open position. Check if resistance changes smoothly in proportion to throttle valve opening angle.
VEHICLE SPEED SENSOR RESISTANCE (1)

Application Ohms
All Models (2)
(1) For testing procedure, see I - SYS/COMP TESTS article in the ENGINE PERFORMANCE Section.
(2) Connect ohmmeter across reed switch terminals and rotate speedometer cable. Ohmmeter reading should fluctuate between continuity and no continuity.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.