Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSDODGE AND RAM2024PROMASTER 3500 BASE, CUTAWAYREPAIR AND DIAGNOSIS (SINGLE PAGE)QUICK LOOKUPSDTC INDEXDTC INDEX (2 OF 2)MODULE, RADIO FREQUENCY (RF HUB)
2024 Dodge and Ram ProMaster 3500 Base, Cutaway
Module, Radio Frequency (RF Hub)
2024 Dodge and Ram ProMaster 3500 Base, CutawaySECTION Module, Radio Frequency (RF Hub)
DIAGNOSTIC CODE INDEX
| DTC | Description |
|---|---|
| B1001-21 | RKE FOB 1 - SIGNAL AMPLITUDE MINIMUM |
| B1001-64 | RKE FOB 1 - SIGNAL PLAUSIBILITY FAILURE |
| B1002-21 | RKE FOB 2 - SIGNAL AMPLITUDE MINIMUM |
| B1002-64 | RKE FOB 2 - SIGNAL PLAUSIBILITY FAILURE |
| B1003-21 | RKE FOB 3 - SIGNAL AMPLITUDE MINIMUM |
| B1003-64 | RKE FOB 3 - SIGNAL PLAUSIBILITY FAILURE |
| B1004-21 | RKE FOB 4 - SIGNAL AMPLITUDE MINIMUM |
| B1004-64 | RKE FOB 4 - SIGNAL PLAUSIBILITY FAILURE |
| B1005-21 | RKE FOB 5 - SIGNAL AMPLITUDE MINIMUM |
| B1005-64 | RKE FOB 5 - SIGNAL PLAUSIBILITY FAILURE |
| B1006-21 | RKE FOB 6 - SIGNAL AMPLITUDE MINIMUM |
| B1006-64 | RKE FOB 6 - SIGNAL PLAUSIBILITY FAILURE |
| B1007-21 | RKE FOB 7 - SIGNAL AMPLITUDE MINIMUM |
| B1007-64 | RKE FOB 7 - SIGNAL PLAUSIBILITY FAILURE |
| B1008-21 | RKE FOB 8 - SIGNAL AMPLITUDE MINIMUM |
| B1008-64 | RKE FOB 8 - SIGNAL PLAUSIBILITY FAILURE |
| B1021-01 | PASSIVE ENTRY OF ANTENNA 1 - GENERAL ELECTRICAL FAILURE |
| B1021-11 | PASSIVE ENTRY OF ANTENNA 1 - CIRCUIT SHORT TO GROUND |
| B1021-12 | PASSIVE ENTRY OF ANTENNA 1 - CIRCUIT SHORT TO BATTERY |
| B1021-13 | PASSIVE ENTRY OF ANTENNA 1 - CIRCUIT OPEN |
| B1022-01 | PASSIVE ENTRY OF ANTENNA 2 - GENERAL ELECTRICAL FAILURE |
| B1022-11 | PASSIVE ENTRY OF ANTENNA 2 - CIRCUIT SHORT TO GROUND |
| B1022-12 | PASSIVE ENTRY OF ANTENNA 2 - CIRCUIT SHORT TO BATTERY |
| B1022-13 | PASSIVE ENTRY OF ANTENNA 2 - CIRCUIT OPEN |
| B1023-01 | PASSIVE ENTRY OF ANTENNA 3 - GENERAL ELECTRICAL FAILURE |
| B1023-11 | PASSIVE ENTRY OF ANTENNA 3 - CIRCUIT SHORT TO GROUND |
| B1023-12 | PASSIVE ENTRY OF ANTENNA 3 - CIRCUIT SHORT TO BATTERY |
| B1023-13 | PASSIVE ENTRY OF ANTENNA 3 - CIRCUIT OPEN |
| B1024-01 | PASSIVE ENTRY OF ANTENNA 4 - GENERAL ELECTRICAL FAILURE |
| B1024-11 | PASSIVE ENTRY OF ANTENNA 4 - CIRCUIT SHORT TO GROUND |
| B1024-12 | PASSIVE ENTRY OF ANTENNA 4 - CIRCUIT SHORT TO BATTERY |
| B1024-13 | PASSIVE ENTRY OF ANTENNA 4 - CIRCUIT OPEN |
| B1025-01 | PASSIVE ENTRY OF ANTENNA 5 - GENERAL ELECTRICAL FAILURE |
| B1025-11 | PASSIVE ENTRY OF ANTENNA 5 - CIRCUIT SHORT TO GROUND |
| B1025-12 | PASSIVE ENTRY OF ANTENNA 5 - CIRCUIT SHORT TO BATTERY |
| B1025-13 | PASSIVE ENTRY OF ANTENNA 5 - CIRCUIT OPEN |
| B1031-01 | IMMOBILIZER ANTENNA - GENERAL ELECTRICAL FAILURE |
| B1032-31 | RF MODULE COMMUNICATION - NO SIGNAL |
| B1033-64 | OPERATIONAL MODE STATUS 1 - SIGNAL PLAUSIBILITY FAILURE |
| B1034-64 | OPERATIONAL MODE STATUS 2 - SIGNAL PLAUSIBILITY FAILURE |
| B1035-01 | BUTTON PRESSED - GENERAL ELECTRICAL FAILURE |
| B1035-71 | BUTTON PRESSED - ACTUATOR STUCK |
| B1036-12 | IGNITION START - CIRCUIT SHORT TO BATTERY |
| B1036-14 | IGNITION START - CIRCUIT SHORT TO GROUND OR OPEN |
| B1039-11 | TRUNK LOCK SWITCH CIRCUIT SHORT TO GROUND |
| B1040-64 | OPERATIONAL MODE STATUS INFO 1 - SIGNAL PLAUSIBILITY FAILURE |
| B1041-16 | RFHM ELECTRIC FAILURE 1 - CIRCUIT VOLTAGE BELOW THRESHOLD |
| B1041-17 | RFHM ELECTRIC FAILURE 1 - CIRCUIT VOLTAGE ABOVE THRESHOLD |
| B1042-42 | RFHM ELECTRIC FAILURE 2 - GENERAL MEMORY FAILURE |
| B1045-01 | FRONT DRIVER DOOR HANDLE SENSE - GENERAL ELECTRICAL FAILURE |
| B1045-11 | FRONT DRIVER DOOR HANDLE SENSE - CIRCUIT SHORT TO GROUND |
| B1045-49 | FRONT DRIVER DOOR HANDLE SENSE - INTERNAL ELECTRONIC FAILURE |
| B1045-64 | FRONT DRIVER DOOR HANDLE SENSE - SIGNAL PLAUSIBILITY FAILURE |
| B1046-01 | FRONT PASSENGER DOOR HANDLE SENSE - GENERAL ELECTRICAL FAILURE |
| B1046-11 | FRONT PASSENGER DOOR HANDLE SENSE - CIRCUIT SHORT TO GROUND |
| B1046-49 | FRONT PASSENGER DOOR HANDLE SENSE - INTERNAL ELECTRONIC FAILURE |
| B1046-64 | FRONT PASSENGER DOOR HANDLE SENSE - SIGNAL PLAUSIBILITY FAILURE |
| B1047-64 | REAR LEFT DOOR HANDLE SENSE - SIGNAL PLAUSIBILITY FAILURE |
| B1048-64 | REAR RIGHT DOOR HANDLE SENSE - SIGNAL PLAUSIBILITY FAILURE |
| B1051-55 | RFHM PROXI PROCEDURE - NOT CONFIGURED |
| B1052-11 | REMOTE START ANTENNA - CIRCUIT SHORT TO GROUND |
| B1052-12 | REMOTE START ANTENNA - CIRCUIT SHORT TO BATTERY |
| B1052-13 | REMOTE START ANTENNA - CIRCUIT OPEN |
| B1053-64 | RFHM (KIN COMMUNICATION) - SIGNAL PLAUSIBILITY FAILURE |
| B1054-13 | BRAKE PEDAL SWITCH - CIRCUIT OPEN |
| B1054-62 | BRAKE PEDAL SWITCH - SIGNAL COMPARE FAILURE |
| B1054-64 | BRAKE PEDAL SWITCH STS1 - SIGNAL PLAUSIBILITY FAILURE |
| B1054-67 | BRAKE PEDAL SWITCH - SIGNAL INCORRECT AFTER EVENT |
| B1054-86 | BRAKE PEDAL SWITCH - SIGNAL INVALID |
| B1055-92 | ECU INTERNAL LF DRIVER - PERFORMANCE OR INCORRECT OPERATION |
| B1056-64 | BRAKE PEDAL SWITCH STS3 - SIGNAL PLAUSIBILITY FAILURE |
| B1057-64 | BRAKE PEDAL SWITCH STS2 - SIGNAL PLAUSIBILITY FAILURE |
| C1501-07 | TIRE PRESSURE SENSOR (FRONT LEFT) - MECHANICAL FAILURES |
| C1501-16 | TIRE PRESSURE SENSOR (FRONT LEFT) - CIRCUIT VOLTAGE BELOW THRESHOLD |
| C1501-31 | TYRE PRESSURE SENSOR FRONT LEFT - NO SIGNAL |
| C1501-64 | TIRE PRESSURE SENSOR (FRONT LEFT) - SIGNAL PLAUSIBILITY FAILURE |
| C1502-07 | TIRE PRESSURE SENSOR (FRONT RIGHT) - MECHANICAL FAILURES |
| C1502-16 | TIRE PRESSURE SENSOR (FRONT RIGHT) - CIRCUIT VOLTAGE BELOW THRESHOLD |
| C1502-31 | TYRE PRESSURE SENSOR FRONT RIGHT - NO SIGNAL |
| C1502-64 | TIRE PRESSURE SENSOR (FRONT RIGHT) - SIGNAL PLAUSIBILITY FAILURE |
| C1503-07 | TIRE PRESSURE SENSOR (REAR LEFT) - MECHANICAL FAILURES |
| C1503-16 | TIRE PRESSURE SENSOR (REAR LEFT) - CIRCUIT VOLTAGE BELOW THRESHOLD |
| C1503-31 | TYRE PRESSURE SENSOR REAR LEFT - NO SIGNAL |
| C1503-64 | TIRE PRESSURE SENSOR (REAR LEFT) - SIGNAL PLAUSIBILITY FAILURE |
| C1504-07 | TIRE PRESSURE SENSOR (REAR RIGHT) - MECHANICAL FAILURES |
| C1504-16 | TIRE PRESSURE SENSOR (REAR RIGHT) - CIRCUIT VOLTAGE BELOW THRESHOLD |
| C1504-31 | TYRE PRESSURE SENSOR REAR RIGHT - NO SIGNAL |
| C1504-64 | TIRE PRESSURE SENSOR (REAR RIGHT) - SIGNAL PLAUSIBILITY FAILURE |
| C1510-54 | TIRE PRESSURE SENSORS CALIBRATION - MISSING CALIBRATION |
| C1512-88 | TPM SENSOR LOCATION UNDETERMINED - BUS OFF |
| C1597-53 | TIRE PRESSURE SENSORS SYSTEM - DEACTIVATED |
| C15CB-51 | TIRE PRESSURE SENSORS PROCEDURE (PLACARD VALUE) - NOT PROGRAMMED |
| U0001-87 | C CAN-MISSING MESSAGE |
| U0001-88 | CAN LINE-BUS OFF |
| U1001-64 | BCM_CODE_TRM_REQUEST - SIGNAL PLAUSIBILITY FAILURE |
| U1700-86 | BODY COMPUTER MODULE (BCM) - SIGNAL INVALID |
| U1700-87 | BCM-BODY CONTROL MODULE-MISSING MESSAGE |
| U1701-86 | ENGINE CONTROL MODULE (ECM) - SIGNAL INVALID |
| U1701-87 | ENGINE CONTROL MODULE (ECM) - MISSING MESSAGE |
| U1703-86 | IPC (INSTRUMENT PANEL CLUSTER) - SIGNAL INVALID |
| U1703-87 | INSTRUMENT PANEL CLUSTER (IPC) - MISSING MESSAGE |
| U1706-86 | BRAKING SYSTEM MODULE (BSM) - SIGNAL INVALID |
| U1706-87 | BRAKING SYSTEM MODULE (BSM) - MISSING MESSAGE |
| U1711-86 | DUAL CLUTCH TRANSMISSION MODULE (DCTM) OR TRANSMISSION CONTROL MODULE (TCM) - SIGNAL INVALID |
| U1711-87 | DUAL CLUTCH TRANSMISSION MODULE (DCTM) OR TRANSMISSION CONTROL MODULE (TCM) - MISSING MESSAGE |
| U1950-64 | RFHM_CRC_MCFAILSTS.INFO - SIGNAL PLAUSIBILITY FAILURE |
| U1950-83 | CRC AND MESSAGE COUNTER BCM_COMMAND - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U1952-64 | IMPLAUSIBLE DATA RECEIVED FROM BRAKE SYSTEM MODULE CAN MESSAGE BRAKE1 INTEGRITY ERROR - SIGNAL PLAUSIBILITY FAILURE |
| U1952-83 | CRC AND MESSAGE COUNTER BRAKE1 - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U1960-64 | IMPLAUSIBLE DATA RECEIVED FROM ENGINE CONTROL MODULE CAN MESSAGE ENGINE1 INTEGRITY ERROR - SIGNAL PLAUSIBILITY FAILURE |
| U1960-83 | CRC AND MESSAGE COUNTER ENGINE1 - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U1964-87 | SC MESSAGE - MISSING MESSAGE |
| U1974-64 | IMPLAUSIBLE DATA RECEIVED FROM SHIFTER MODULE CAN MESSAGE SC INTEGRITY ERROR - SIGNAL PLAUSIBILITY FAILURE |
| U1974-83 | CRC AND MESSAGE COUNTER SC MESSAGE - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U197C-64 | IMPLAUSIBLE DATA RECEIVED FROM TRANSMISSION CONTROL MODULE CAN MESSAGE TRANSM2 INTEGRITY ERROR - SIGNAL PLAUSIBILITY FAILURE |
| U197C-83 | CRC AND MESSAGE COUNTER TRANSM2 - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U1982-83 | CRC AND MESSAGE COUNTER WHEEL INFO MESSAGE - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U1984-83 | CRC AND MESSAGE COUNTER WHEEL SPEED MESSAGE - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U2051-87 | BCM CODE TRM REQUEST MESSAGE - MISSING MESSAGE |
| U2052-87 | BATTERY_INFO MESSAGE - MISSING MESSAGE |
| U2053-87 | BCM COMMAND MESSAGE 1 - MISSING MESSAGE |
| U2054-87 | BCM COMMAND MESSAGE 2 - MISSING MESSAGE |
| U2055-87 | BCM COMMAND MESSAGE 3 - MISSING MESSAGE |
| U2056-87 | BODY2 MESSAGE - MISSING MESSAGE |
| U2058-87 | BODY4 MESSAGE - MISSING MESSAGE |
| U2059-87 | BODY4 FAST MESSAGE - MISSING MESSAGE |
| U2061-87 | BRAKE 1 MESSAGE - MISSING MESSAGE |
| U2062-87 | CLUSTER 1 (KEY IDENTIFICATION VF) MESSAGE - MISSING MESSAGE |
| U2063-87 | CLUSTER 1 (VIN VF) MESSAGE - MISSING MESSAGE |
| U2064-87 | CLUSTER 2 (REMOTE CONTROL VF) MESSAGE - MISSING MESSAGE |
| U2065-87 | ENGINE 1 (KEYLESS IGNITION VF) MESSAGE - MISSING MESSAGE |
| U2066-87 | ENGINE 1 (IGNITION WORKING CONDITION VF) MESSAGE - MISSING MESSAGE |
| U2067-87 | MOT TRANSM4 MESSAGE - MISSING MESSAGE |
| U2068-87 | TIME AND DATE MESSAGE - MISSING MESSAGE |
| U2069-87 | TRANSM2 MESSAGE - MISSING MESSAGE |
| U2070-87 | VIN MESSAGE - MISSING MESSAGE |
| U2071-67 | BCM COMMAND MESSAGE IN SNA STATUS - SIGNAL INCORRECT AFTER EVENT |
| U2072-64 | BODY4 PLAUSIBILITY MESSAGE - SIGNAL PLAUSIBILITY FAILURE |
| U2073-64 | BRAKE 1 PLAUSIBILITY MESSAGE - SIGNAL PLAUSIBILITY FAILURE |
| U2081-87 | WHEEL SPEED MESSAGE - MISSING MESSAGE |
| U2082-87 | WHEEL INFO MESSAGE - MISSING MESSAGE |
| U2083-64 | EXTERNAL TEMPERATURE MESSAGE - SIGNAL PLAUSIBILITY FAILURE |
| U2083-87 | EXTERNAL TEMPERATURE MESSAGE - MISSING MESSAGE |
| U2084-87 | TIRE PRESSURE SENSOR INFO - MISSING MESSAGE |
| U2085-64 | ATMOSPHERIC PRESSURE MESSAGE - SIGNAL PLAUSIBILITY FAILURE |
| U2086-64 | BCM COMMAND BRAKEPEDALSWITCH - SIGNAL PLAUSIBILITY FAILURE |
| U2087-64 | BCM_COMMAND.OPERATIONALMODESTS - SIGNAL PLAUSIBILITY FAILURE |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.