Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSDODGE AND RAM2024PROMASTER 3500 BASE, CUTAWAYREPAIR AND DIAGNOSIS (SINGLE PAGE)ACCESSORIES & EQUIPMENTDRIVERS ASSISTANCE SYSTEMS - ADASFORWARD FACING CAMERA MODULE (FFCM) - DTCS B1006-49 TO U0121-00
2024 Dodge and Ram ProMaster 3500 Base, Cutaway
Forward Facing Camera Module (FFCM) - DTCS B1006-49 To U0121-00
2024 Dodge and Ram ProMaster 3500 Base, CutawaySECTION Forward Facing Camera Module (FFCM) - DTCS B1006-49 To U0121-00
- DTC Troubleshooting
- B1006-49 Half (Haptic Lane Feedback) - Internal Electronic Failure
- B1007-54 Half (Haptic Lane Feedback) - Missing Calibration
- B1EAB-00 Steering Wheel Cruise Control Switch
- B1EAB-86 Steering Wheel Cruise Control Switch - Signal Invalid
- B210A-00 System Voltage Low - No Subtype Information
- B210B-00 System Voltage High - No Subtype Information
- B2206-00 Current VIN Mismatch - No Subtype Information
- C0031-64 Left Front Wheel Speed Sensor - Signal Plausibility Failure
- C0034-64 Right Front Wheel Speed Sensor - Signal Plausibility Failure
- C0037-64 Left Rear Wheel Speed Sensor - Signal Plausibility Failure
- C003A-64 Right Rear Wheel Speed Sensor - Signal Plausibility Failure
- C003F-00 Wheel Speed Sensors Rotation Direction Correlation - No Subtype Information
- C0061-64 Lateral Acceleration Sensor - Signal Plausibility Failure
- C0062-64 Longitudinal Acceleration Sensor - Signal Plausibility Failure
- C0063-29 Yaw Rate Sensor - Signal Signal Invalid
- C0063-64 Yaw Rate Sensor - Signal Plausibility Failure
- C10F6-53 Brake Rolls Mode Active - Deactivated
- C1226-64 Brake Pedal Master Cylinder Pressure - Signal Plausibility Failure
- C1260-00 Abs/ESC Dynamic Controls Disabled - No Subtype Information
- C1407-86 Acknowledge Signal Fail From Brake System Module (BSM) - Signal Invalid
- C1409-97 Radar - Component Or System Operation Obstructed Or Blocked
- C140C-86 Half Intervention Request Time Out Of Range - Signal Invalid
- C1413-86 External Light Signal Fault - Signal Invalid
- C1415-53 Forward Collision Warning (FCW) Unavailable - Deactivated
- C1422-00 Internal HW Plausibility Check - No Subtype Information
- C1432-86 Turn Indicator Failure From Body Control Module (BCM) - Signal Invalid
- C1433-86 External Brake Signal Failure From Brake System Module (BSM) - Signal Invalid
- C1434-86 Brake Jerk Request Not Plausible - Signal Invalid
- C1436-86 Electric Parking Brake System Fail - Signal Invalid
- C1451-86 Acc (Adaptive Cruise Control) Safe - Signal Invalid
- C1453-86 Acc (Adaptive Cruise Control) Intervention Signals Not Plausible - Signal Invalid
- C14A5-92 Sensor Blinded - Performance Or Incorrect Operation
- C14A5-97 Sensor Blinded - Component Or System Operation Obstructed Or Blocked
- C14AA-64 Sensor Adjustment Required - Signal Plausibility Failure
- C1600-94 Supplier Mode Active - Unexpected Operation
- C2210-4B Ecu OVERTEMPERATURE - Over Temperature
- P0780-68 Gear Shift Malfunction - Event Information
- P1C81-00 Shift Lever Position Indeterminate - No Subtype Information
- P1DCB-64 Reverse Gear Switch - Signal Plausibility Failure
- U0055-00 Can C2 Bus-No Subtype Information
- U0056-00 Can C2 Bus Off Performance-No Subtype Information
- U0100-00 Lost Communication With ECM - No Subtype Information
- U0121-00 Loss Of Communication With Brake System Module (BSM) - No Subtype Information
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.