Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSDODGE AND RAM2024PROMASTER 3500 BASE, CUTAWAYREPAIR AND DIAGNOSIS (SINGLE PAGE)ACCESSORIES & EQUIPMENTCOLLISION/AVOIDANCE(RIGHT BLIND SPOT SENSOR MODULE (BSM) (RBSS) - ELECTRICAL DIAGNOSTICS)
2024 Dodge and Ram ProMaster 3500 Base, Cutaway
(Right Blind Spot Sensor Module (BSM) (RBSS) - Electrical Diagnostics)
2024 Dodge and Ram ProMaster 3500 Base, CutawaySECTION (Right Blind Spot Sensor Module (BSM) (RBSS) - Electrical Diagnostics)
- Diagnostic Code Index
- DTC Troubleshooting
- C1000-44 Electronic Control Unit - Data Memory Failure
- C1000-45 Electronic Control Unit - Program Memory Failure
- C1000-46 Electronic Control Unit - Calibration/Parameter Memory Failure
- C1000-47 Electronic Control Unit - Watchdog/Safety MC Failure
- C1003-04 Blind Spot Sensor Problem - System Internal Failures
- C1003-49 Blind Spot Sensor Problem - Internal Electronic Failure
- C1003-78 Blind Spot Sensor Problem - Alignment Or Adjustment Incorrect
- C1003-97 Blind Spot Sensor Problem - Component Or System Operation Obstructed Or Blocked
- C1004-16 Battery Voltage Input Circuit - Circuit Voltage Below Threshold
- C1004-17 Battery Voltage Input Circuit - Circuit Voltage Above Threshold
- C1005-02 RBSS Radar Sensor Address Fault - General Signal Failure
- C100A-11 Right Blind Spot Sensor - Circuit Short To Ground
- C100A-15 Right Blind Spot Sensor - Circuit Short To Battery Or Open
- C2000-64 Status_TTM.TRAILERCONNECTIONSTS - Signal Plausibility Failure
- C2001-64 IGN Line And Status_BCM.KEYSTS - Signal Plausibility Failure
- C2002-64 External_Lights.TURNLIGHTACTIVATIONSTS - Signal Plausibility Failure
- C2003-64 Vehicle_Speed_Odometer.VEHICLESPEEDFAILSTS - Signal Plausibility Failure
- C2004-64 IPC_Vehicle_Setup.BSDENABLE - Signal Plausibility Failure
- C2005-64 RBSS_OPERATIONALMODESTS - Signal Plausibility Failure
- C2006-64 Dynamic_Vehicle_Info4.LWSFAILSTS - Signal Plausibility Failure
- C2007-64 Dynamic_Vehicle_Info2.YRSSTAT - Signal Plausibility Failure
- C2010-64 VIN Mismatch - Signal Plausibility Failure
- U0010-88 B Can - Bus Off
- U0100-87 Private Can - Missing Message
- U0100-88 Private Can - Bus Off
- U1700-86 Body Computer Module (BCM) - Signal Invalid
- U1700-87 Body Control Module (BCM) - Missing Message
- U1703-86 Instrument Panel Cluster (IPC) - Signal Invalid
- U1703-87 Instrument Panel Cluster (IPC) - Missing Message
- U1751-86 Left Blind Spot Sensor (LBSS) - Signal Invalid
- U1751-87 Left Blind Spot Sensor (LBSS) - Missing Message
- U1763-86 TTM (Trailer Tow Module)-Signal Invalid
- U1763-87 TTM (Trailer Tow Module)-Missing Message
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.