Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Torque Specifications
2024 Dodge and Ram 1500 TRXSECTION Torque Specifications
WARNING: This page is about a different variant/trim than selected.
| DESCRIPTION | N. m | Ft. Lbs. | In. Lbs. | COMMENT |
|---|---|---|---|---|
| 48V+ Nut to MGU | 18 | 13 | - | |
| 48 Volt Harness Trough To Stud Bracket Nuts | 11 | 8 | - | |
| 48 Volt Harness Trough To Rear Floor | 6 | - | 53 | |
| 48 Volt Harness Trough To Engine Bracket Nuts | 11 | 8 | - | |
| B+ Battery Positive at Power Distribution Center (PDC) M6 | 8 | - | 71 | |
| B+ Battery Positive at Power Distribution Center (PDC) M8 | 12 | 9 | - | |
| Battery Negative to Negative Post | 7 | - | 62 | |
| Battery Negative to Engine | 30 | 22 | - | |
| Battery Positive Cable | 7 | - | 62 | |
| Battery Positive to Positive Post | 7 | - | 62 | |
| Battery Bracket Bolt - Battery Hold Down to Tray | 5 | - | 44 | |
| Battery Tray Bolts | 10 | - | 89 | |
| Generator to Front Cover | 28 | 21 | - | |
| Intelligent Battery Sensor (IBS) Sensor to Negative Post | 7 | - | 62 | |
| Jumper to MGU | 11 | 8 | - | |
| 48 Volt Cable to MGU | 18 | 13 | ||
| MGU Studs to Engine 3.6L | 10 | - | 89 | |
| MGU Nuts to Studs 3.6L | 62 | 46 | - | |
| MGU Bolt to Cylinder Head 3.6L | 62 | 46 | - | |
| BSG Cable to MGU Bracket 3.6L | 9 | - | 80 | |
| MGU Harness Trough To Cylinder Head Cover Nut | 11 | 8 | - | |
| Negative Battery Cable to the IBS | 7 | - | 62 | |
| Battery Negative Lead to Fender | 20 | 15 | - | |
| Negative Battery Cable to Engine Block | 20 | 15 | - | |
| Pencil Brace M8 Bolt to MGU | Specific Torque Sequence. Refer to: TORQUE SPECIFICATIONS . | |||
| Pencil Brace M8 Bolts to Valve Cover Brace | Specific Torque Sequence. Refer to: TORQUE SPECIFICATIONS . | |||
| PDC to Wiring Connector | 4 | - | 35 | |
| PDC to B+ | 12 | 9 | - | |
| PDC Tray To Cross Beam Nuts |
8 | - | 71 | |
| Power Pack Unit (PPU) Ground to Body Nut | 20 | 15 | - | |
| PPU Ground Stud Nut | 20 | 15 | - | |
| PPU to PPU Bracket Lower | 20 | 15 | - | |
| PPU to PPU Bracket Upper | 20 | 15 | - | |
| PPU 12 Volt Connection Nut | 20 | 15 | - | |
| PPU 48 Volt Connection Nut | 20 | 15 | - | |
| PPU Upper Bracket To Cab Back Bolt | 20 | 15 | - | |
| PPU Lower Bracket To Floor | 46 | 34 | - | |
| PPU Wiring Shield Nuts | 8 | - | 71 | |
| Starter Bolt to Transmission 3.6L | 55 | 41 | - | |
| Starter B+ Nut | 11 | 8 | - | |
| Tensioner to MGU | 55 | 41 | - | |
| Wiring From MGU to PPU Nuts | 6 | - | 53 | |
| Wiring Trough to Studs in Rear Floor | 5 | - | 44 | |
| Wiring Pass Through Nuts in Rear Floor | 6 | - | 53 | |
| Wiring Breakout Block Underhood Nuts | 6 | - | 53 | |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.