SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSDODGE AND RAM20241500 TRXREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 209 (SPEED CONTROL (SERVICE INFORMATION) - 1500)SWITCH, SPEED CONTROLREMOVAL AND INSTALLATIONTRX SPEED CONTROL SWITCH
2024 Dodge and Ram 1500 TRX

TRX Speed Control Switch

2024 Dodge and Ram 1500 TRXSECTION TRX Speed Control Switch
WARNING: This page is about a different car, the 2023 RAM 1500. However, it is still accessible from the selected car via links, so may be relevant.

REMOVAL 

WARNING:

To avoid serious or fatal injury on vehicles equipped with airbags, disable the Supplemental Restraint System (SRS) before attempting any steering wheel, steering column, airbag, seat belt tensioner, impact sensor or instrument panel component diagnosis or service. Disconnect and isolate the battery negative (ground) cable, then wait two minutes for the system capacitor to discharge before performing further diagnosis or service. This is the only sure way to disable the SRS. Failure to take the proper precautions could result in accidental airbag deployment.

  1. Disconnect and isolate the negative battery cable(s). Refer to BATTERY DISCONNECT AND CONNECT - SINGLE 12V BATTERY SYSTEM, 3.0L & 5.7L EZH or BATTERY DISCONNECT AND CONNECT - ETORQUE SYSTEM, 3.6L & 5.7L EZL or BATTERY DISCONNECT AND CONNECT - SINGLE 12V BATTERY SYSTEM, 6.2L .
  2. Remove the driver air bag. Refer to AIRBAG, REMOVAL AND INSTALLATION .
    GC0199467Courtesy of CHRYSLER GROUP, LLC
  3. Remove the covers (1) and the fasteners (2) from the back of the steering wheel (3).
    GC0199260Courtesy of CHRYSLER GROUP, LLC
  4. Remove the fasteners (1) from the steering wheel bezel (2) and remove the bezel from the steering wheel (3). Disconnect the wire harness connectors.
    GC0199413Courtesy of CHRYSLER GROUP, LLC
  5. Remove the fastener (1) and the switch closeout (2) from the steering wheel bezel (3).
    GC0199432Courtesy of CHRYSLER GROUP, LLC
  6. Remove the fasteners (1) the speed control switch (3) from the steering wheel bezel (2).

INSTALLATION 

GC0199432Courtesy of CHRYSLER GROUP, LLC
  1. Position the speed control switch (3) into the steering wheel bezel (2).
  2. Install and securely tighten the fasteners (1) for the speed control switch.
    GC0199413Courtesy of CHRYSLER GROUP, LLC
  3. Install the switch close out (2) to the steering wheel bezel (3). Install and securely tighten the fastener (1).
    GC0199260Courtesy of CHRYSLER GROUP, LLC
  4. Position the steering wheel bezel (2) to the steering wheel (3) and connect the wire harness connectors.
  5. Install and securely tighten the fasteners (1) for the bezel.
    GC0199467Courtesy of CHRYSLER GROUP, LLC
  6. Install and securely tighten the fasteners (2) to the back of the steering wheel (3). Install the covers (1).
  7. Install the driver air bag. Refer to AIRBAG, REMOVAL AND INSTALLATION .
  8. Connect the negative battery cable(s). Refer to BATTERY DISCONNECT AND CONNECT - SINGLE 12V BATTERY SYSTEM, 3.0L & 5.7L EZH or BATTERY DISCONNECT AND CONNECT - ETORQUE SYSTEM, 3.6L & 5.7L EZL or BATTERY DISCONNECT AND CONNECT - SINGLE 12V BATTERY SYSTEM, 6.2L .
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.