Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSDODGE AND RAM2023PROMASTER 3500 CUTAWAYREPAIR AND DIAGNOSIS (SINGLE PAGE)ACCESSORIES & EQUIPMENTDRIVERS ASSISTANCE SYSTEMS - ADAS(LEFT BLIND SPOT SENSOR MODULE (BSM) (LBSS) - ELECTRICAL DIAGNOSTICS)
2023 Dodge and Ram ProMaster 3500 Cutaway
(Left Blind Spot Sensor Module (BSM) (LBSS) - Electrical Diagnostics)
2023 Dodge and Ram ProMaster 3500 CutawaySECTION (Left Blind Spot Sensor Module (BSM) (LBSS) - Electrical Diagnostics)
- Diagnostic Code Index
- DTC Troubleshooting
- C1000-44-Electronic Control Unit - Data Memory Failure
- C1000-45-Electronic Control Unit - Program Memory Failure
- C1000-46-Electronic Control Unit - Calibration/Parameter Memory Failure
- C1000-47-Electronic Control Unit - Watchdog/Safety MC Failure
- C1002-02-LBSS Radar Sensor Address Fault - General Signal Failure
- C1003-04-Blind Spot Sensor Problem - System Internal Failures
- C1003-49-Blind Spot Sensor Problem - Internal Electronic Failure
- C1003-78-Blind Spot Sensor Problem - Alignment Or Adjustment Incorrect
- C1003-97-Blind Spot Sensor Problem - Component Or System Operation Obstructed Or Blocked
- C1004-16-Battery Voltage Input Circuit - Circuit Voltage Below Threshold
- C1004-17-Battery Voltage Input Circuit - Circuit Voltage Above Threshold
- C100B-11-Left Blind Spot Sensor - Circuit Short To Ground
- C100B-15-Left Blind Spot Sensor - Circuit Short To Battery Or Open
- C2000-64-Status_TTM.TRAILERGENERICFAILSTS - Signal Plausibility Failure
- C2001-64-Status_CCAN5.SHIFTLEVERPOSITION - Signal Plausibility Failure
- C2002-64-Status_BH_BCM2.TURNINDICATIONSTS - Signal Plausibility Failure
- C2003-64-Status_CCAN3.VEHICLESPEEDVSOSIGFAILSTS - Signal Plausibility Failure
- C2004-64-IPC_Vehicle_Setup.BSDENABLE - Signal Plausibility Failure
- C2005-64-LBSS_OPERATIONALMODESTS - Signal Plausibility Failure
- C2006-64-Status_CCAN5.LWSANGLE Status_CCAN5.LWSANGLEFAILSTS - Signal Plausibility Failure
- C2007-64-Status_CCAN1.YAWRATE_BSM Status_CCAN1.YAWRATEFAILSTS_BSM - Signal Plausibility Failure
- C2008-64-Engine1.REVERSEGEARSTS - Signal Plausibility Failure
- C2009-64-TMA And TTM Trailer Detection - Signal Plausibility Failure
- C2010-64-VIN Mismatch - Signal Plausibility Failure
- U0010-88-B Can - Bus Off
- U1700-86-Body Computer Module (BCM) - Signal Invalid
- U1700-87-Body Control Module (BCM) - Missing Message
- U1703-86-Instrument Panel Cluster (IPC) - Signal Invalid
- U1703-87-Instrument Panel Cluster (IPC) - Missing Message
- U1752-86-Right Blind Spot Sensor (RBSS) - Signal Invalid
- U1752-87-Right Blind Spot Sensor (RBSS) - Missing Message
- U1763-86-TTM (Trailer Tow Module)-Signal Invalid
- U1763-87-TTM (Trailer Tow Module)-Missing Message
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.