Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSDODGE AND RAM2023PROMASTER 1500REPAIR AND DIAGNOSIS (SINGLE PAGE)QUICK LOOKUPSDTC INDEXDTC INDEX (1 OF 2)MODULE, ELECTRIC POWER STEERING (EPS)
2023 Dodge and Ram ProMaster 1500
Module, Electric Power Steering (EPS)
2023 Dodge and Ram ProMaster 1500SECTION Module, Electric Power Steering (EPS)
DIAGNOSTIC CODE INDEX
| DTC | Description |
|---|---|
| C0528-00 | STEERING ANGLE SENSOR MODULE RANGE/PERFORMANCE - NO SUBTYPE INFORMATION |
| C0529-00 | STEERING ANGLE SENSOR MODULE MISSING CALIBRATION - NO SUBTYPE INFORMATION |
| C1005-68 | ELECTRIC POWER STEERING (EPS) LAMP FAILURE - EVENT INFORMATION |
| C1007-86 | ESS ENG ST SIGNAL FROM C1 IGW1 MESSAGE NOT VALID - SIGNAL INVALID |
| C1010-86 | MAX RATE FROM BRAKE SYSTEM MODULE (BSM) - SIGNAL INVALID |
| C1011-85 | MAX VALUE FROM HALF MODULE (HALF) - SIGNAL INVALID |
| C1012-85 | MAX RATE FROM HALF MODULE (HALF) - SIGNAL ABOVE ALLOWABLE RANGE |
| C1013-49 | HALF MODULE FAULTY - INTERNAL ELECTRONIC FAILURE |
| C1013-86 | HALF MODULE FAULTY - SIGNAL INVALID |
| C1014-86 | PARKING AID MODULE (PAM) INCORRECT DEACTIVATION - SIGNAL INVALID |
| C1015-92 | PARKING AID MODULE (PAM) - PERFORMANCE OR INCORRECT OPERATION |
| C1016-85 | PARKING AID MODULE (PAM) - SIGNAL ABOVE ALLOWABLE RANGE |
| C1017-86 | DRIVESTYLE STS SIGNAL FROM BODY2 MESSAGE NOT VALID - SIGNAL INVALID |
| C101A-54 | NO TUNING SET INSTALLED - MISSING CALIBRATION |
| C1200-FF | ENGINEERING DTC - EPS |
| C1214-62 | CONF DATA CODE REQUEST MESSAGE - SIGNAL COMPARE FAILURE |
| C1214-87 | CONF DATA CODE REQUEST MESSAGE - MISSING MESSAGE |
| C1214-FF | ENGINEERING DTC - EPS |
| C1230-51 | BODY CONTROL MODULE (BCM) PROXI NOT PROGRAMMED - NOT PROGRAMMED |
| C1592-01 | ELECTRONIC POWER STEERING MOTOR CIRCUIT - GENERAL ELECTRICAL FAILURE |
| C1593-49 | STEERING TORQUE SENSOR CIRCUIT - INTERNAL ELECTRONIC FAILURE |
| C2129-16 | BATTERY VOLTAGE - CIRCUIT VOLTAGE BELOW THRESHOLD |
| C2129-17 | BATTERY VOLTAGE - CIRCUIT VOLTAGE ABOVE THRESHOLD |
| C2129-1C | BATTERY VOLTAGE - CIRCUIT VOLTAGE OUT OF RANGE |
| C2129-1F | BATTERY VOLTAGE - CIRCUIT INTERMITTENT |
| C2202-00 | ORIGINAL VIN MISSING - NO SUBTYPE INFORMATION |
| C2203-00 | CURRENT VIN MISMATCH - NO SUBTYPE INFORMATION |
| C2205-49 | STEERING ANGLE SENSOR INTERNAL - INTERNAL ELECTRONIC FAILURE |
| C2205-64 | STEERING ANGLE SENSOR INTERNAL - SIGNAL PLAUSIBILITY FAILURE |
| C2210-4B | ELECTRIC POWER STEERING (EPS) OVER TEMPERATURE - OVER TEMPERATURE |
| C2217-48 | ELECTRIC POWER STEERING MODULE INTERNAL - SUPERVISION SOFTWARE FAILURE |
| C2217-49 | ELECTRIC POWER STEERING MODULE INTERNAL - INTERNAL ELECTRONIC FAILURE |
| U0055-00 | CAN C2 BUS - NO SUBTYPE INFORMATION |
| U0056-00 | CAN C2 BUS OFF PERFORMANCE - NO SUBTYPE INFORMATION |
| U0100-00 | ENGINE CONTROL MODULE -ECM-PCM- CAN SIGNAL - MISSING MESSAGE |
| U0129-00 | LOST COMMUNICATION WITH BRAKE SYSTEM CONTROL MODULE |
| U0140-00 | LOST COMMUNICATION WITH BODY CONTROL MODULE |
| U0155-00 | LOST COMMUNICATION WITH INSTRUMENT PANEL CLUSTER IPC CONTROL MODULE |
| U0159-00 | LOST COMMUNICATION FROM PARKING AID MODULE (PAM) - NO SUBTYPE INFORMATION |
| U0279-00 | LOSS OF COMMUNICATION WITH HAPTIC LANE FEEDBACK MODULE (HALF) - NO SUBTYPE INFORMATION |
| U0401-83 | IMPLAUSIBLE DATA RECEIVED FROM ENGINE CONTROL MODULE (ECM-PCM) - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U0418-64 | IMPLAUSIBLE DATA RECEIVED FROM BRAKE SYSTEM CONTROL MODULE 1-SIGNAL PLAUSIBILITY FAILURE |
| U0422-83 | IMPLAUSIBLE DATA RECEIVED FROM BODY CONTROL MODULE (BCM) - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U045A-83 | IMPLAUSIBLE DATA RECEIVED FROM PARKING AID MODULE (PAM) - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U0580-00 | IMPLAUSIBLE DATA RECEIVED FROM HAPTIC LANE FEEDBACK MODULE (HALF) - NO SUBTYPE INFORMATION |
| U0580-83 | IMPLAUSIBLE DATA RECEIVED FROM HAPTIC LANE FEEDBACK MODULE (HALF) - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U1422-87 | CL IGW1 MESSAGE FROM BODY CONTROL MODULE (BCM) IS MISSING - MISSING MESSAGE |
| U1930-86 | INTERNAL IGNITION WORKING CONDITION SIGNAL - SIGNAL INVALID |
| U1952-83 | MESSAGE COUNTER/CRC FAULT ON BRAKE1 MESSAGE - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
| U1982-83 | MESSAGE COUNTER/CRC FAULT ON WHEEL INFO MESSAGE - VALUE OF SIGNAL PROTECTION CALCULATION INCORRECT |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.