Safety Warning

DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.

SYS.OK|MANUAL.DB● LIVE

HOMESERVICE MANUALSDODGE AND RAM2023DURANGO SRT 392 PLUSREPAIR AND DIAGNOSIS (SINGLE PAGE)ACCESSORIES & EQUIPMENTCOLLISION/AVOIDANCE(FORWARD FACING CAMERA MODULE (FFCM) - ELECTRICAL DIAGNOSTICS)DTC TROUBLESHOOTINGC2210-00-ECU OVERTEMPERATUREDIAGNOSTIC TEST

2023 Dodge and Ram Durango SRT 392 Plus

Diagnostic Test

2023 Dodge and Ram Durango SRT 392 PlusSECTION Diagnostic Test

READ AND RECORD DTCS AND ENVIRONMENTAL DATA - ERASE DTCS AND CHECK FOR DTC TO RETURN
1. With the scan tool, read DTCs in all Electronic Control Units (ECUs) and record on the repair order.
2. With the scan tool, run a vehicle Scan Report, or record the Environmental Data related to the DTCs.
3. With the scan tool, erase all DTCs.
4. Turn the ignition off for a minimum of 10 seconds.
5. Turn the ignition on.
6. Wait a minimum of 90 seconds.
7. With the scan tool, read DTCs.
  Did the DTC return?
  
  Yes
  - Go To 2
  No
  - Perform the TESTING FOR AN INTERMITTENT CONDITION diagnostic procedure. Refer to TESTING FOR AN INTERMITTENT CONDITION .
MOVE VEHICLE TO A COOLER ENVIRONMENT - ERASE DTCS AND CHECK FOR DTC TO RETURN
1. Move the vehicle to a cooler environment until the FFCM ambient temperature is below 85° C (185° F).
2. With the scan tool, erase FFCM DTCs.
3. Turn the ignition off for a minimum of 10 seconds.
4. Turn the ignition on.
5. Wait a minimum of 90 seconds.
6. With the scan tool, read DTCs.
  Did the DTC return?
  
  Yes
  - Go To 3
  No
  - Moving the vehicle to a cooler environment corrected the condition.
  - Perform the FORWARD FACING CAMERA VERIFICATION TEST. Refer to STANDARD PROCEDURE .
CHECK RELATED HARNESS CONNECTIONS
1. Turn the ignition off.
2. Disconnect all FFCM harness connectors.
3. Disconnect all related in-line harness connections (if equipped).
4. Disconnect the related component harness connectors.
5. Inspect harness connectors, component connectors, and all male and female terminals for the following conditions:
  - Proper connector installation.
  - Damaged connector locks.
  - Corrosion.
  - Other signs of water intrusion.
  - Weather seal damage (if equipped).
  - Bent terminals.
  - Overheating due to a poor connection (terminal may be discolored due to excessive current draw).
  - Terminals that have been pushed back into the connector cavity.
  - Perform a terminal drag test on each connector terminal to verify proper terminal tension.
  Repair any conditions that are found.
6. Reconnect all FFCM harness connectors. Be certain that all harness connectors are fully seated and the connector locks are fully engaged.
7. Reconnect all in-line harness connectors (if equipped). Be certain that all connectors are fully seated and the connector locks are fully engaged.
8. Reconnect all related component harness connectors. Be certain that all connectors are fully seated and the connector locks are fully engaged.
9. With the scan tool, erase DTCs.
10. Turn the ignition off for a minimum of 10 seconds.
11. Turn the ignition on.
12. Wait a minimum of 90 seconds.
13. With the scan tool, read FFCM DTCs.
  Did the DTC return?
  
  Yes
  - Replace the Forward Facing Camera Module (FFCM) in accordance with the Service Information. Refer to MODULE, FORWARD FACING CAMERA (FFCM), REMOVAL and Refer to MODULE, FORWARD FACING CAMERA (FFCM), INSTALLATION .
  - Perform the FORWARD FACING CAMERA VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  No
  - Perform the FORWARD FACING CAMERA VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  - Test complete.

RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready Tools Free Quote Check Quote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

• You smell fuel, burning insulation, or see smoke.
• Brakes feel soft, pull hard to one side, or make grinding noises.
• The engine overheats, stalls repeatedly, or misfires under load.
• You are missing required tools, torque specs, or safe lifting equipment.
• You are not confident in the next step or safety outcome.