Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSDODGE AND RAM2023DURANGO GT, RWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT VARIANT/TRIMSECTION 11 (8HP95 AUTOMATIC TRANSMISSION (SERVICE INFORMATION))SPECIAL TOOLS
2023 Dodge and Ram Durango GT, RWD
Special Tools
2023 Dodge and Ram Durango GT, RWDSECTION Special Tools
WARNING: This page is about a different variant/trim than selected.
| 1130 - Splitter, Bearing/Gear (Originally Shipped In Kit Number(s) 6745, 6947, 6949, 9202, 9202A-CAN, 9202CC, 9299.) |
|
| 6787A - Remover, Bearing Cup (Originally Shipped In Kit Number(s) 6784, 6809.) |
|
| 6936 - Spacer (Originally Shipped In Kit Number(s) 6945, 6946, 6947, 6948.) |
|
| 8285 - Compressor, Spring (Originally Shipped In Kit Number(s) 8283, 8283CC, 8527, 8527CC, 8575, 8575CC, 9975.) |
|
| 8481 - Installer, Gear (Originally Shipped In Kit Number(s) 8708, 8708CC.) |
|
| 8901A - Pressing Tool (Originally Shipped In Kit Number(s) 8901A.) |
|
| 8925-3 - Assembly, Press Fixture (Originally Shipped In Kit Number(s) 8998, 8998CC.) |
|
| 9585 - Remover, Bearing Cup (Originally Shipped In Kit Number(s) 9691.) |
|
| 9664 - Remover, Bearing Cup (Originally Shipped In Kit Number(s) 9675, 9685, 9695.) |
|
| 9667 - Remover, Seal (Originally Shipped In Kit Number(s) 9691.) |
|
| 9677 - Installer, Seal (Originally Shipped In Kit Number(s) 9675, 9685, 9695.) |
|
| 10373A - Installer, Output Needle Bearing/Rear Oil Dam (Originally Shipped In Kit Number(s) 10394A.) |
|
| 10375 - Installer, Oil Pump Cover Oil Seal | |
| 10376 - Installer, Input Shaft Needle Bearing (Originally Shipped In Kit Number(s) 10394A, 10394-UPD.) |
|
| 10377 - Remover/Installer, Guide Sleeve | |
| 10378 - Rings, Support | |
| 10379 - Pins, Valve Body Alignment | |
| 10382 - Installer, Oil Pump Housing Needle Bearing (Originally Shipped In Kit Number(s) 10394A, 10394-UPD.) |
|
| 10383 - Plate, Clutch Pressure Test | |
| 10428 - Adapter, Pressing Tool (Originally Shipped In Kit Number(s).) |
|
| 10429 - Gauge, Force (Originally Shipped In Kit Number(s) 10419.) |
|
| C-637 - Slide Hammer, Universal (Originally Shipped In Kit Number(s) 9202.) |
|
| C-3281 - Holder, Flange (Originally Shipped In Kit Number(s) 9202, 9202A-CAN, 9202CC, 9299, 9299CC, 9299CC, 9300A-CAN.) |
|
| C-3752 - Slide Hammers (Originally Shipped In Kit Number(s) 9202, 9202A-CAN, 9202-CAN, 9202CC.) |
|
| C-4171 - Driver Handle, Universal (Originally Shipped In Kit Number(s) 9202, 9202A-CAN, 9202CC, 9299, 9299CC, 9299CC, 9300A-CAN.) |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.