Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSDODGE AND RAM2023CHARGER SXT, 4WDREPAIR AND DIAGNOSISSUSPENSIONWHEEL ALIGNMENTFRONT SUSPENSION & WHEEL ALIGNMENTFRONTTECHNICAL SPECIFICATIONSTORQUE SPECIFICATIONS
2023 Dodge and Ram Charger SXT, 4WD
Torque Specifications
2023 Dodge and Ram Charger SXT, 4WDSECTION Torque Specifications
| DESCRIPTION | N.m | Ft. Lbs. | In. Lbs. | COMMENT |
|---|---|---|---|---|
| Front Active Damping Sensor Bolt | 10 | - | 89 | |
| Hub And Bearing Bolts AWD | 68 | 50 | - | |
| Hub And Bearing Bolts RWD | 100 | 74 | - | |
| Hub Nut - AWD | 213 | 157 | - | |
| Hub Nut - RWD | 230 | 170 | - | |
| Lower Ball Joint to Knuckle Nut | 37 + 180° | 27 + 180° | - | Do not reuse fastener. If removed, a new fastener must be installed and tightened to specifications. |
| Lower Control Arm to Cradle Bolt and Nut | 185 | 136 | - | |
| Lower Control Arm to Cradle Bolt and Nut (AWD) | 175 | 129 | - | |
| Rear Active Damping Sensor Bolt | 10 | - | 89 | |
| Shock Absorber Shaft Nut | 100 | 74 | - | |
| Stabilizer Bar to Crossmember Bolts | 65 | 48 | - | |
| Stabilizer Bar Heat Shield to Crossmember Bolts | 5 | - | 44 | |
| Stabilizer Link to Stabilizer Bar Nut | 135 | 100 | - | |
| Stabilizer Link to Strut Nut | 150 | 111 | - | |
| Strut Clevis to Lower Control Arm RWD | 174 | 128 | - | |
| Strut Clevis to Lower Control Arm AWD | 170 | 125 | - | Bolt Held Nut Torqued |
| Strut Clevis to Strut Pinch Bolt | 61 | 45 | - | |
| Strut Mount to Body Nut | 27 | 20 | - | |
| Strut to Lower Control Arm Bolt | 174 | 128 | - | |
| Tension Strut to Cradle Bolt and Nut | 178 | 131 | - | |
| Tension Strut to Knuckle Bolt and Nut | 37+ 180° | 27+ 180° | - | Do not reuse fastener. If removed, a new fastener must be installed and tightened to specifications. |
| Upper Ball Joint to Knuckle Nut | 40 + 90° | 30 + 90° | - | |
| Upper Control Arm to Body Bolt and Nut | 90 | 66 | - |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.