Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSDODGE AND RAM2023CHARGER SXT, 4WDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT VARIANT/TRIMSECTION 2 (6.4L ENGINE (SERVICE INFORMATION))TECHNICAL SPECIFICATIONSTORQUE SPECIFICATIONS
2023 Dodge and Ram Charger SXT, 4WD
Torque Specifications
2023 Dodge and Ram Charger SXT, 4WDSECTION Torque Specifications
WARNING: This page is about a different variant/trim than selected.
ENGINE BLOCK
| DESCRIPTION | N. m | Ft. Lbs. | In. Lbs. | COMMENT |
|---|---|---|---|---|
| Camshaft Phaser Bolt | 122 | 90 | - | |
| Camshaft Thrust Plate Bolts | 12 | - | 106 | |
| Coolant Drain Plugs 1/4 x 18 NPT | 34 | 25 | - | |
| Connecting Rod Cap Bolts | 40 plus 90° Turn | 30 plus 90° Turn | - | |
| Crankshaft Main Bearing Cap Bolts | Specific torque and fastener pattern required; follow installation sequence. Refer to CRANKSHAFT, INSTALLATION . | |||
| Engine Oil Cooler to Engine Block | 33 | 24 | - | |
| Lifter Guide Holder | 12 | 9 | - | |
| MDS Solenoid - Bolts | 11 | 8 | - | |
| Oil Pan Bolts | Specific torque and fastener pattern required; follow installation sequence. Refer to PAN, OIL, INSTALLATION . | Do not reuse these fasteners. If removed, a NEW fastener must be installed and tightened to specifications. | ||
| Oil Dipstick Tube | 12 | 9 | - | |
| Oil Gallery Plugs 1/4 x 18 NPT | 20 | 15 | - | |
| Oil Pan Drain Plug | 27 | 20 | - | |
| Oil Pressure Sensor | 35 | 27 | - | |
| Oil Pump to Engine Block Bolts | 19 | 14 | - | |
| Oil Pump Cover Bolts. | 15 | 11 | - | |
| Oil Pump Pickup Tube Bolt | 28 | 21 | - | |
| Oil Pump Pickup Tube Nut | 28 | 11 | - | |
| Oil Temperature Sensor | 50 | 37 | - | |
| Piston Oil Cooler Jet Bolts | 13 | 10 | - | |
| Plugs 3/8 x 18 NPT | 27 | 20 | - | |
| Timing Chain Guide Bolts | 12 | 9 | - | |
| Timing Chain Tensioner Bolts | 12 | 9 | - | |
| Variable Valve Timing Solenoid Bolt | 11 | 8 | - | |
CYLINDER HEAD
| DESCRIPTION | N. m | Ft. Lbs. | In. Lbs. | COMMENT |
|---|---|---|---|---|
| Cylinder Head Bolts | Specific torque and fastener pattern required. Refer to CYLINDER HEAD, INSTALLATION . | |||
| Cylinder Head Cover Bolts | 11 | - | 97 | |
| Exhaust Manifold Bolts | 30 | 22 | - | |
| Exhaust Manifold Heat Shield Bolts | 9 | - | 80 | |
| Ignition Coil Bolts | 7 | - | 62 | |
| Intake Manifold Bolts | Specific torque and fastener pattern required. Refer to MANIFOLD, INTAKE, INSTALLATION . | |||
| Lifter Guide Holder Bolts | 12 | 9 | - | |
| Rocker Arm Bolts | Specific torque and fastener pattern required. Refer to ROCKER ARM, VALVE, INSTALLATION . | |||
FRONT ENGINE
| DESCRIPTION | N. m | Ft. Lbs. | In. Lbs. | COMMENT |
|---|---|---|---|---|
| Timing Chain Cover Bolts | 28 | 21 | - | |
| Lifting Stud | 55 | 41 | - | |
| Vibration Damper Bolt | 176 | 130 | - |
REAR ENGINE
| DESCRIPTION | N. m | Ft. Lbs. | In. Lbs. | COMMENT |
|---|---|---|---|---|
| Flexplate Bolts | 95 | 70 | - | Do not reuse these fasteners. If removed, a NEW fastener must be installed and tightened to specifications. |
| Inspection Cover to Transmission Bolt | 11 | 8 | - | |
| Rear Crankshaft Oil Seal Retainer Bolts | 15 | 11 | - | |
| Torque Convertor Bolts | 42 | 31 | - | |
| Transmission to Oil Pan Bolts | 45 | 33 | - | |
| Transmission Bell Housing to Engine Bolts | 45 | 33 | - |
ENGINE MOUNTS
| DESCRIPTION | N. m | Ft. Lbs. | In. Lbs. | COMMENT |
|---|---|---|---|---|
| Engine Mount Bracket to Block Bolts | 61 | 45 | - | |
| Engine Mount to Engine Mount Bracket | 52 | 38 | - | |
| Engine Mount to Cradle Bolts | 48 | 35 | - | |
| Engine Mount Heat Shield Nuts | 25 | 18 | - | |
| Transmission Crossmember Bolts - Automatic | 65 | 48 | - | |
| Transmission Crossmember Bolts - Manual | 61 | 45 | - | |
| Rear Isolator Bracket to Transmission Bolts (Automatic) | 61 | 45 | - | |
| Rear Isolator to Bracket Bolts (Automatic) | 31 | 23 | - | |
| Rear Isolator to Crossmember Bolts (Automatic) | 61 | 45 | - | |
| Rear Isolator to Transmission Bolts (Manual) | 54 | 40 | - | |
| Rear Isolator to Crossmember Bolts (Manual) | 54 | 40 | - |
ACCESSORY DRIVE
| DESCRIPTION | N. m | Ft. Lbs. | In. Lbs. | COMMENT |
|---|---|---|---|---|
| Generator Support Bracket Bolt | 65 | 48 | - | |
| Generator Support Bracket to Engine Mount Nut | 25 | 18 | - |
MISCELLANEOUS COMPONENTS
| DESCRIPTION | N. m | Ft. Lbs. | In. Lbs. | COMMENT |
|---|---|---|---|---|
| Air Cleaner Body Bolt | 5 | - | 44 | |
| Air Cleaner Cover | 3 | - | 30 | |
| Air Cleaner Tube Clamps | 4 | - | 35 | |
| Catalytic Converter to Exhaust Manifold Nuts | 11 | 8 | - | |
| Engine Wiring Harness Bracket to Engine | 18 | 13 | - | |
| Oil Control Valve Bolt | 11 | 8 | - | |
| Heater Tube Bolt | 18 | 13 | - | |
| Strut Tower Support Bolts | 38 | 28 | - |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.