Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSDODGE AND RAM2023CHALLENGER SXT, RWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT VARIANT/TRIMSECTION 4 (TR6060 MANUAL TRANSMISSION (SERVICE INFORMATION) (6.2L))TECHNICAL SPECIFICATIONSTORQUE SPECIFICATIONS
2023 Dodge and Ram Challenger SXT, RWD
Torque Specifications
2023 Dodge and Ram Challenger SXT, RWDSECTION Torque Specifications
WARNING: This page is about a different variant/trim than selected.
| DESCRIPTION | N.m | Ft. Lbs. | In. Lbs. | COMMENT |
|---|---|---|---|---|
| Adapter Bolts | 34 | 25 | - | |
| Back Up Lamp Switch | 34 | 25 | - | |
| Bottom Transmission To Oil Pan Bolts | 45 | 33 | - | |
| Clutch Housing Bolts | 34 | 25 | - | |
| Clutch Release Bearing/Slave Cylinder Bolts | 28 | 21 | - | |
| Crossmember Bolts | 61 | 45 | - | |
| Drain Plug | 27 | 20 | - | |
| Extension Housing Bolts | 48 | 33 | - | |
| Extension Housing Nuts | 48 | 35 | - | |
| Fill Plug | 27 | 20 | - | |
| *Flywheel Bolts | 75 | 55 | - | Do not reuse these fasteners. If removed, a NEW fastener must be installed and tightened to specifications. |
| Front Transmission To Engine Bolts | 45 | 33 | - | |
| Guide Plate Bolts | 22 | 16 | - | |
| Inspection Cover Bolt | 11 | - | 95 | |
| Output Flange Nut | 60 | 44 | - | |
| * Reverse Idler Bracket Bolts | 30 | 22 | - | |
| Reverse Lockout Solenoid Bolt | 18 | 13 | - | |
| * Roller Detent Bolt | 40 | 30 | - | |
| Shifter Assembly Bolts | 19 | - | 168 | |
| Shift Lever Bolts | 19 | - | 168 | |
| *Shift Lever Guide Bolts | 27 | 20 | - | |
| * Side Shift Detent | 40 | 30 | - | |
| Skip Shift Solenoid | 34 | 25 | - | |
| Top Cover Bolts | 20 | 15 | - | |
| Top Transmission To Engine Studs | 45 | 33 | - | |
| Transmission Isolator To Crossmember Nuts | 54 | 40 | - | |
| Transmission Isolator To Transmission Bolts | 33 | 24 | - | |
| * Needs application of Mopar Lock AND Seal Adhesive or equivalent | ||||
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.