Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSDODGE AND RAM20151500 SPECIAL SERVICEREPAIR AND DIAGNOSIS (SINGLE PAGE)QUICK LOOKUPSDTC INDEX - 1500MODULE, STEERING CONTROL (SCM)
2015 Dodge and Ram 1500 Special Service
Module, Steering Control (SCM)
2015 Dodge and Ram 1500 Special ServiceSECTION Module, Steering Control (SCM)
DIAGNOSTIC CODE INDEX
| DTC | Description |
|---|---|
| B1425-2A | REMOTE RADIO SWITCH INPUT - STUCK |
| B1504-2A | LEFT STEERING WHEEL CONTROL SWITCH - STUCK |
| B2306-2A | FRONT WASHER SWITCH - STUCK |
| B232E-00 | REAR WASHER SWITCH - STUCK |
| B2332-2A | HORN SWITCH - STUCK |
| B23A1-2A | FLASH TO PASS/OPTICAL HORN SWITCH - STUCK |
| C1219-00 | STEERING ANGLE SENSOR ERRATIC PERFORMANCE |
| C121A-00 | STEERING ANGLE SENSOR NOT INITIALIZED |
| C123F-00 | STEERING ANGLE SENSOR COMPARATIVE PERFORMANCE |
| C1240-76 | STEERING ANGLE SENSOR ANGLE OVERTRAVEL PERFORMANCE - WRONG MOUNTING POSITION |
| C1241-00 | STEERING ANGLE SENSOR VELOCITY PERFORMANCE |
| C2129-16 | BATTERY VOLTAGE - CIRCUIT VOLTAGE BELOW THRESHOLD |
| C2129-17 | BATTERY VOLTAGE - CIRCUIT VOLTAGE ABOVE THRESHOLD |
| C212A-16 | SYSTEM VOLTAGE - CIRCUIT VOLTAGE BELOW THRESHOLD |
| C212A-17 | SYSTEM VOLTAGE - CIRCUIT VOLTAGE ABOVE THRESHOLD |
| C2205-00 | STEERING ANGLE SENSOR INTERNAL |
| P0579-00 | SPEED CONTROL SWITCH 1 PERFORMANCE |
| P0580-00 | SPEED CONTROL SWITCH 1 CIRCUIT LOW |
| P0581-00 | SPEED CONTROL SWITCH 1 CIRCUIT HIGH |
| P0585-00 | SPEED CONTROL SWITCH 1/2 CORRELATION |
| P0591-00 | SPEED CONTROL SWITCH 2 PERFORMANCE |
| P0592-00 | SPEED CONTROL SWITCH 2 CIRCUIT LOW |
| P0593-00 | SPEED CONTROL SWITCH 2 CIRCUIT HIGH |
| P1593-2A | SPEED CONTROL SWITCH 1/2 STUCK |
| U0002-00 | CAN C BUS OFF PERFORMANCE |
| U0100-00 | LOST COMMUNICATION WITH PCM |
| U0146-00 | LOST COMMUNICATION WITH CENTRAL GATEWAY |
| U0155-00 | LOST COMMUNICATION WITH CLUSTER/CCN |
| U1008-00 | LIN 1 BUS |
| U1009-00 | LIN 2 BUS |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.