Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Leak Testing
The normal operating temperature of the exhaust system is very high. Therefore, never work around or attempt to service any part of the exhaust system until it is cooled. Special care should be taken when working near the catalytic converter. The temperature of the converter rises to a high level after a short period of engine operation time.
- Raise and support vehicle.CAUTION:
The air pressure must not exceed 4 psi, otherwise engine damage can occur.
- Connect Tool (special tool #8404-EC, Exhaust Cone) or (special tool #8404-ECT, Exhaust Cone, Truck), Exhaust Cone to an adjustable air pressure regulator.
- Attach shop air to the air pressure regulator.
- Adjust the air pressure regulator to 4 psi
- Insert Tool (special tool #8404-EC, Exhaust Cone) or (special tool #8404-ECT, Exhaust Cone, Truck), Exhaust Cone into the vehicle tail pipe.
- If the vehicle is equipped with dual exhaust, use Tool (special tool #8404-EC, Exhaust Cone) or (special tool #8404-ECT, Exhaust Cone, Truck), Exhaust Cone with equipped attached plug. Plug one side of the dual exhaust pipe. Pressurize the other as described.
- Apply a mixture of liquid dish soap and water to the following areas:
- - All welded joints from 6 inches rearward of the downstream O2 sensor forward
- - O2 sensor seal points
- - O2 sensor boss welds
- - Flange/joint connection(s)
- - Exhaust manifold to cylinder head connection(s)
- - EGR solenoid gasket base and tube seal points (if equipped)
- Watch for the liquid/soapy water to bubble.
- Use the following definitions to help determine if system or component repair/replacement is necessary:
- Type 1 Leak is defined as a leak where very small foam like bubbles 1mm (.039 in.) or less appear. Any Type 1 or greater leaks found in welded joints, O2 sensor seal points or O2 sensor boss welds must be repaired or the component must be replaced.
- Type 2 Leak is defined as a leak where larger bubbles 8mm (.031 in.) or greater appear. Any Type 2 or greater leaks found in flange or joint connections, exhaust manifold to cylinder head connections, or EGR gasket and tube seal points must be repaired or the components must be replaced.
| Leak Location | Repair required if results at 4 psi reveal bubble size: |
|---|---|
| Welded joints | Type 1 - 1 mm (.039 in.) or greater |
| O2 Sensor seal points | Type 1 - 1 mm (.039 in.) or greater |
| O2 Sensor boss welds | Type 1 - 1 mm (.039 in.) or greater |
| Flange/joint connections | Type 2 - 8 mm (.031 in.) or greater |
| Exhaust Manifold to cylinder head connections | Type 2 - 8 mm (.031 in.) or greater |
| EGR gasket and tube seal points | Type 2 - 8 mm (.031 in.) or greater |
If a leak is found that matches the above definition, repair or replace the component as necessary.
Once the repair is complete, repeat the procedure to verify that all leaks have been repaired.
NO RELATED
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.