SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSDODGE AND RAM2013JOURNEY CREW, AWDREPAIR AND DIAGNOSIS (SINGLE PAGE)ACCESSORIES & EQUIPMENTENTERTAINMENT SYSTEMSTELEMATICS GATEWAY MODULE - ELECTRICAL DIAGNOSTICSDTC TROUBLESHOOTINGB140C-11-REAR RIGHT AUDIO SPEAKER OUTPUT - CIRCUIT SHORT TO GROUND- PREMIUMDIAGNOSTIC TEST
2013 Dodge and Ram Journey Crew, AWD

Diagnostic Test

2013 Dodge and Ram Journey Crew, AWDSECTION Diagnostic Test
  1. CHECK FOR AN INTERMITTENT CONDITION 
    1. Turn the ignition on and open one of the front doors.
      NOTE:

      A front door must remain open whenever checking or erasing TGW DTCs.

    2. Using the scan tool, record and erase the TGW DTCs.
    3. Cycle the ignition switch from on to off, wait five seconds and then back to on.
    4. Turn the Radio on and set the volume to 25.
    5. Adjust the speakers to the Rear and center.
    6. Using the scan tool, read the active TGW DTCs.

      Does the scan tool display active: B140C-11-REAR RIGHT AUDIO SPEAKER OUTPUT - CIRCUIT SHORT TO GROUND?

      Yes 

      • Go To  2

      No 

      • Test complete, the condition or conditions that originally set this DTC are not present at this time. Using the wiring diagrams as a guide, check all related splices and connectors for signs of water intrusion, corrosion, pushed out or bent terminals and correct pin tension.
      • Perform the BODY VERIFICATION TEST. Refer to STANDARD PROCEDURE .
  2. CHECK THE AMPLIFIER 
    Fig 1: Amplifier Connector End View
    GC0137447Courtesy of CHRYSLER GROUP, LLC
    1. Make sure one of the front doors is still open.
    2. Using the scan tool, erase the DTCs.
    3. Turn the ignition off.
    4. Disconnect the Amplifier harness connector.
    5. Turn the ignition on.
    6. Turn the radio on and set the volume to 25.
    7. Using the scan tool, read the active TGW DTCs.

      Does the scan tool display active: B140C-11-REAR RIGHT AUDIO SPEAKER OUTPUT - CIRCUIT SHORT TO GROUND?

      Yes 

      • Go To  3

      No 

  3. CHECK THE (X52) RIGHT REAR AUDIO (+) CIRCUIT FOR A SHORT TO GROUND 
    Fig 2: Checking Right Rear Audio (+) Circuit For Short To Ground
    GC0150555Courtesy of CHRYSLER GROUP, LLC
    1. Turn the ignition off.
    2. Disconnect the TGW harness connector.
    3. Measure the resistance between ground and the (X52) Right Rear Audio (+) circuit.

      Is the resistance below 5.0 Ohms?

      Yes 

      • Repair the (X52) Right Rear Audio (+) circuit for a short to ground.
      • Perform the BODY VERIFICATION TEST. Refer to STANDARD PROCEDURE .

      No 

      • Go To  4
  4. CHECK THE (X58) RIGHT REAR AUDIO (-) CIRCUIT FOR A SHORT TO GROUND 
    Fig 3: Checking Right Rear Audio (-) Circuit For Short To Ground
    GC0150556Courtesy of CHRYSLER GROUP, LLC
    1. Measure the resistance between ground and the (X58) Right Rear Audio (-) circuit.

      Is the resistance below 5.0 Ohms?

      Yes 

      • Repair the (X58) Right Rear Audio (-) for a short to ground.
      • Perform the BODY VERIFICATION TEST. Refer to STANDARD PROCEDURE .

      No 

RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.