Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSDODGE AND RAM2013DART GTREPAIR AND DIAGNOSISGENERAL INFORMATIONDTC INDEXMODULE, ELECTRIC POWER STEERING (EPS)
2013 Dodge and Ram Dart GT
Module, Electric Power Steering (EPS)
2013 Dodge and Ram Dart GTSECTION Module, Electric Power Steering (EPS)
DIAGNOSTIC CODE INDEX
| DTC | Description |
|---|---|
| C0051-04 | STEERING WHEEL POSITION SENSOR - SYSTEM INTERNAL FAILURES |
| C0051-2F | STEERING WHEEL POSITION SENSOR - SIGNAL ERRATIC |
| C0051-31 | STEERING WHEEL POSITION SENSOR - NO SIGNAL |
| C0051-54 | STEERING WHEEL POSITION SENSOR - MISSING CALIBRATION |
| C1592-01 | ELECTRONIC POWER STEERING MOTOR CIRCUIT - GENERAL ELECTRICAL FAILURE |
| C1592-16 | ELECTRONIC POWER STEERING MOTOR CIRCUIT - CIRCUIT VOLTAGE BELOW THRESHOLD |
| C1592 | ELECTRIC POWER STEERING MOTOR CIRCUIT - SIGNAL INVALID |
| C1592-4B | ELECTRONIC POWER STEERING MOTOR CIRCUIT - OVER TEMPERATURE |
| C1592-74 | ELECTRONIC POWER STEERING MOTOR CIRCUIT - ACTUATOR SLIPPING |
| C1592-98 | ELECTRONIC POWER STEERING MOTOR CIRCUIT - COMPONENT OR SYSTEM OVER TEMPERATURE |
| C15C1-00 | EPS MECHANICAL PERFORMANCE |
| C15CA-00 | BRAKE SYSTEM MODULE - EVENT INFORMATION |
| C2100-16 | BATTERY VOLTAGE LOW - CIRCUIT VOLTAGE BELOW THRESHOLD |
| C2101-17 | BATTERY VOLTAGE HIGH - CIRCUIT VOLTAGE ABOVE THRESHOLD |
| C2129-13 | BATTERY VOLTAGE - CIRCUIT OPEN |
| C2202-00 | ORIGINAL VIN MISMATCH/MISSING |
| C2217-00 | ELECTRIC POWER STEERING MODULE INTERNAL |
| C221C-00 | ECU FLASH REQUIRED |
| C221F-00 | ECU NOT INITIALIZED |
| U0001-87 | CAN-C BUS MISSING MESSAGE |
| U0002-00 | CAN C BUS OFF PERFORMANCE |
| U0100-00 | LOST COMMUNICATION WITH ECM/PCM |
| U0121-00 | LOST COMMUNICATION WITH ANTI-LOCK BRAKE SYSTEM (ABS) CONTROL MODULE |
| U0140-00 | LOST COMMUNICATION WITH BODY CONTROL MODULE (BCM) |
| U0401-86 | IMPLAUSIBLE DATA RECEIVED FROM ECM/PCM - SIGNAL INVALID |
| U0415-00 | IMPLAUSIBLE DATA RECEIVED FROM ABS |
| U0415-86 | IMPLAUSIBLE DATA RECEIVED FROM ABS - SIGNAL INVALID |
| U0422-00 | IMPLAUSIBLE DATA RECEIVED FROM BODY CONTROL MODULE |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.