Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2012 Chrysler 300 C, RWDFACTORY OEM SERVICE PROCEDURE
External Pages
These are pages that do not belong to the exact selected vehicle (2012 Chrysler 300 C, RWD), but are still accessible from a link in your vehicle's manual. Be very cautious using repair info from here because these pages may not apply to your vehicle.
- Different variant/trim
- Section 1 (Front Half Shaft)
- Section 2 (Front Axle)
- Section 3 (8HP45 Automatic Transmission (Service Information))
- Section 4 (3.6L Engine (Service Information))
- Section 5 (6.4L Engine (Service Information))
- Section 6 (BW44-40 Transfer Case (Service Information))
- Section 7 (Amplifier (Amp) - Electrical Diagnostics - SRT8)
- Section 8 (Active Damping Control Module (ADCM) Electrical Diagnostics - SRT8)
- Section 9 (Electronic Shift Module (ESM) - Electrical Diagnostics - 8HP45 Automatic Transmission)
- Section 10 (3.6L - Diagnostic Code Index)
- Section 11 (3.6L - DTCS P000A To P0159)
- Section 12 (3.6L - DTCS P0160 To P0481)
- Section 13 (3.6L - DTCS P0501 To P1128)
- Section 14 (3.6L - DTCS P1129 To P2245)
- Section 15 (3.6L - DTCS P2246 To U1431)
- Section 16 (3.6L - Intermittent Condition, Pcm/ECM Programming - Gas, Powertrain Verification Test & Pre-Diagnostic Troubleshooting Procedure)
- Section 17 (6.4L - Diagnostic Code Index)
- Section 18 (6.4L - DTCS P000B To P0201)
- Section 19 (6.4L - DTCS P0202 To P0521)
- Section 20 (6.4L - DTCS P0522 To P1521)
- Section 21 (6.4L - DTCS P1524 To P2302)
- Section 22 (6.4L - DTCS P2305 To U1431)
- Section 23 (6.4L - Intermittent Condition, Pcm/ECM Programming - Gas, Powertrain Verification Test & Pre-Diagnostic Troubleshooting Procedure)
- Section 24 (Transmission Control Module (TCM) - Diagnostic Code Index - 8HP45 Automatic Transmission)
- Section 25 (Transmission Control Module (TCM) - DTCS P0219 To P1D93 - 8HP45 Automatic Transmission)
- Section 26 (Transmission Control Module (TCM) - DTCS P1D94 To U1479 - 8HP45 Automatic Transmission)
- Section 27 (Transmission Control Module (TCM) - Pre-Diagnostic Troubleshooting Procedure, Verification Test, TCM Programming Procedure & TCM Adaptation - 8HP45 Automatic Transmission)
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.