Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2012 ChryslerFACTORY OEM SERVICE PROCEDURE
Chrysler: 2012
- 200
- LX, 2.4L Eng VIN B, Eng CD ED3, Trans Mfr CD 40TE
- LX, 2.4L Eng VIN B, Eng CD ED3, Trans Mfr CD 62TE
- LX, 2.4L Eng VIN B, Eng CD EDG, Trans Mfr CD 40TE
- LX, 2.4L Eng VIN B, Eng CD EDG, Trans Mfr CD 62TE
- LX, 3.6L Eng VIN G
- Limited, 2D Convertible
- Limited, 4D Sedan, 2.4L Eng VIN B, Eng CD ED3
- Limited, 4D Sedan, 2.4L Eng VIN B, Eng CD EDG
- Limited, 4D Sedan, 3.6L Eng VIN G
- S, 2D Convertible
- S, 4D Sedan
- Touring, 2D Convertible, 2.4L Eng VIN B, Eng CD ED3
- Touring, 2D Convertible, 2.4L Eng VIN B, Eng CD EDG
- Touring, 2D Convertible, 3.6L Eng VIN G
- Touring, 4D Sedan, 2.4L Eng VIN B, Eng CD ED3
- Touring, 4D Sedan, 2.4L Eng VIN B, Eng CD EDG
- Touring, 4D Sedan, 3.6L Eng VIN G
- 300
- Base, Trans Mfr CD 8HP45, Gas
- Base, Trans Mfr CD 8HP45, Gas/Ethanol
- Base, Trans Mfr CD NAG1-W5A580, Gas
- Base, Trans Mfr CD NAG1-W5A580, Gas/Ethanol
- C Luxury, 4WD
- C Luxury, RWD
- C, 4WD
- C, RWD
- Limited, 4WD, Gas
- Limited, 4WD, Gas/Ethanol
- Limited, RWD, Gas
- Limited, RWD, Gas/Ethanol
- S, 3.6L Eng VIN G, 4WD, Gas
- S, 3.6L Eng VIN G, 4WD, Gas/Ethanol
- S, 3.6L Eng VIN G, RWD, Gas
- S, 3.6L Eng VIN G, RWD, Gas/Ethanol
- S, 5.7L Eng VIN T, 4WD
- S, 5.7L Eng VIN T, RWD
- SRT-8
- Town & Country
- 200
- 300 AWD
- 300 RWD
- 300 RWD SRT-8 V8-6.4L
- Town & Country V6-3.6L
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.