Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2012 Chrysler 200 S, 2D ConvertibleFACTORY OEM SERVICE PROCEDURE
Engine Cooling System: Specifications: Torque
| DESCRIPTION | N.m | Ft. Lbs. | In. Lbs. |
|---|---|---|---|
| Fastener-Accessory Drive Belt Tensioner Assembly(2.4L) | 54 | 40 | - |
| Fastener-Accessory Drive Belt Tensioner (2.4L) | 24 | 18 | - |
| Fastener-Accessory Drive Belt Tensioner (3.6L) | 55 | 41 | - |
| Fastener-Idler Pulley (2.4L) | 35 | 26 | - |
| Fastener-Idler Pulley (3.6L) | 25 | 18 | - |
| Fasteners-A/C Condenser to Radiator | 5 | - | 44 |
| Fastener-Block Heater (3.6L) | 12 | 9 | 106 |
| Bolts-Coolant Outlet Connector (3.6L) | 12 | 9 | 106 |
| Cooling System Bleed Valve | 12 | 9 | 106 |
| ETC Sensor (2.4L) | 19 | 14 | - |
| ETC Sensor (3.6L) | 11 | 8 | - |
| Fasteners-Fan Module to Radiator | 5 | - | 44 |
| Fasteners-Fan Motor to Shroud | 5 | - | 44 |
| Bolts-Thermostat Housing (3.6L) | 12 | 9 | 106 |
| Bolts-Thermostat Housing to cylinder head (2.4L) | 28 | 21 | - |
| Fastener-Transmission Cooler Tube Bracket | 5 | - | 44 |
| Fastener-Transmission Cooler Tube | 9 | - | 80 |
| Fitting - Transmission oil cooler quick connect fitting | 15 | 11 | - |
| Bolts-Water Pump (3.6L) | Β | Β | Β |
| M6 | 12 | 9 | 106 |
| M8 | 25 | 18 | - |
| M10 | 55 | 41 | - |
| Hose Clamps-Transmission Cooler | 3 | - | 27 |
| Bolts-Water Pump Mounting (2.4L) | 24 | 18 | - |
| Bolts-Water Pump Inlet Tube to Block (2.4L) | 12 | 9 | 106 |
| Bolts-EGR Bypass assembly-to EGR Cooler body | 10 | 7 | 89 |
| Bolts-EGR Tube -to-Exhaust manifold | 20 | 15 | - |
| Bolts, Water Pump Inlet Tube to water pump housing (2.4L) | 24 | 18 | - |
| Bolts, Water Pump to Water Pump Adapter (2.4L) | 22 | 16 | - |
| Bolts, Water Pump Pulley to Water Pump (2.4L) | 9 | - | 80 |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
