Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHRYSLER2005SEBRING CONVERTIBLE V6-2.7L VIN RREPAIR AND DIAGNOSISPOWERTRAIN MANAGEMENTCOMPUTERS AND CONTROL SYSTEMSRELAYS AND MODULES - COMPUTERS AND CONTROL SYSTEMSENGINE CONTROL MODULETESTING AND INSPECTIONPCM/ECM/SKIM PROGRAMMING
2005 Chrysler Sebring Convertible V6-2.7L VIN R
PCM/ECM/SKIM Programming
2005 Chrysler Sebring Convertible V6-2.7L VIN RSECTION PCM/ECM/SKIM Programming
The SKIS Secret Key is an ID code that is unique to each SKIM. This code is programmed and stored in the SKIM, PCM and transponder chip (ignition
keys). When replacing the PCM it is necessary to program the secret key into the new PCM using the scan tool. Perform the following steps to program the secret key into the PCM.
1. Turn the ignition switch on (transmission in park/neutral).
2. Use the scan tool and select THEFT ALARM, SKIM then MISCELLANEOUS.
3. Select PCM REPLACED (GAS ENGINE).
4. Enter secured access mode by entering the vehicle four-digit PIN.
5. Select ENTER to update PCM VIN.
NOTE: If three attempts are made to enter secure access mode using an incorrect PIN, secured access mode will be locked out for one hour. To exit this lockout mode, turn the ignition to the RUN position for one hour then enter the correct PIN. (Ensure all accessories are turned off. Also monitor the battery state and connect a battery charger if necessary).
6. Press ENTER to transfer the secret key (the SKIM will send the secret key to the PCM).
7. Press Page Back to get to the Select System menu and select ENGINE, MISCELLANEOUS, and SRI MEMORY CHECK.
8. The scan tool will ask, Is odometer reading between XX and XX? Select the YES or NO button on the scan tool. If NO is selected, the scan tool will read, Enter odometer Reading. Enter the odometer reading from the Instrument Panel and press ENTER.
keys). When replacing the PCM it is necessary to program the secret key into the new PCM using the scan tool. Perform the following steps to program the secret key into the PCM.
1. Turn the ignition switch on (transmission in park/neutral).
2. Use the scan tool and select THEFT ALARM, SKIM then MISCELLANEOUS.
3. Select PCM REPLACED (GAS ENGINE).
4. Enter secured access mode by entering the vehicle four-digit PIN.
5. Select ENTER to update PCM VIN.
NOTE: If three attempts are made to enter secure access mode using an incorrect PIN, secured access mode will be locked out for one hour. To exit this lockout mode, turn the ignition to the RUN position for one hour then enter the correct PIN. (Ensure all accessories are turned off. Also monitor the battery state and connect a battery charger if necessary).
6. Press ENTER to transfer the secret key (the SKIM will send the secret key to the PCM).
7. Press Page Back to get to the Select System menu and select ENGINE, MISCELLANEOUS, and SRI MEMORY CHECK.
8. The scan tool will ask, Is odometer reading between XX and XX? Select the YES or NO button on the scan tool. If NO is selected, the scan tool will read, Enter odometer Reading
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.