Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHRYSLER2005CROSSFIRE SRT-6 V6-3.2L SC VIN NREPAIR AND DIAGNOSISRELAYS AND MODULESRELAYS AND MODULES - TRANSMISSION AND DRIVETRAINRELAYS AND MODULES - A/TCONTROL MODULESERVICE AND REPAIR
2005 Chrysler Crossfire SRT-6 V6-3.2L SC VIN N
Control Module: Service and Repair
2005 Chrysler Crossfire SRT-6 V6-3.2L SC VIN NSECTION Service and Repair
REMOVAL
1. Un-snap and remove the carpet floor mat.
2. Fold back the carpeting in the passenger footwell to expose the foam insulation panel.
3. Remove the foam insulation panel.
NOTE: It is not necessary to remove the electrical connectors to rotate the base plate in the passenger footwell.
4. Remove the three plastic retaining nuts (1) from the floor panel studs.
5. Lift the base plate and rotate the top of the base plate toward the rear of the vehicle to expose the TCM.
6. Remove the two retaining screws (1) from the base plate, and disconnect the TCM harness connectors.
7. Remove the TCM (2) from the base plate.
INSTALLATION
1. Connect the TCM harness connectors and attach the TCM (2) to the base plate with the two retaining screws (1).
2. Rotate the base plate and install it over the mounting studs on the floor panel.
NOTE: Be sure not to pinch or cause interference with the wiring harnesses while locating the base plate to the floor mounting studs.
3. Install the three plastic retaining nuts (1) and secure the base plate to the vehicle floor.
4. Install the foam insulation panel.
NOTE: Make sure the aligning tabs of the base plate are positioned correctly in the foam insulating panel.
5. Install the carpeting in the passenger footwell.
6. Install the floor mat to the carpet.
1. Un-snap and remove the carpet floor mat.
2. Fold back the carpeting in the passenger footwell to expose the foam insulation panel.
3. Remove the foam insulation panel.
NOTE: It is not necessary to remove the electrical connectors to rotate the base plate in the passenger footwell.
4. Remove the three plastic retaining nuts (1) from the floor panel studs.
5. Lift the base plate and rotate the top of the base plate toward the rear of the vehicle to expose the TCM.
6. Remove the two retaining screws (1) from the base plate, and disconnect the TCM harness connectors.
7. Remove the TCM (2) from the base plate.
INSTALLATION
1. Connect the TCM harness connectors and attach the TCM (2) to the base plate with the two retaining screws (1).
2. Rotate the base plate and install it over the mounting studs on the floor panel.
NOTE: Be sure not to pinch or cause interference with the wiring harnesses while locating the base plate to the floor mounting studs.
3. Install the three plastic retaining nuts (1) and secure the base plate to the vehicle floor.
4. Install the foam insulation panel.
NOTE: Make sure the aligning tabs of the base plate are positioned correctly in the foam insulating panel.
5. Install the carpeting in the passenger footwell.
6. Install the floor mat to the carpet.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.