Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHRYSLER2004PT CRUISER TOURING, 2.4 B, AUTOMATICREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 2 (ENGINE CONTROLS - SELF-DIAGNOSTICS)DIAGNOSTIC TESTSDTC P1489: HIGH SPEED FAN CONTROL RELAY CIRCUITTESTING
2004 Chrysler PT Cruiser Touring, 2.4 B, Automatic
DTC P1489: High Speed Fan Control Relay Circuit: Testing
2004 Chrysler PT Cruiser Touring, 2.4 B, AutomaticSECTION Testing
WARNING: This page is about a different car, the 2002 Chrysler PT Cruiser. However, it is still accessible from the selected car via links, so may be relevant.
- Turn the ignition on. With the DRBIII®, actuate the High Speed Radiator Fan Relay. Is the High Speed Radiator Fan Relay operating? If yes, go to next step. If no, go to step 4.
- With the DRBIII®, actuate the High Speed Radiator Fan Relay. Wiggle the wiring harness from the High Speed Radiator Fan Relay to the PCM while the relay is actuating. Did the High Speed Radiator Fan Relay stop when wiggling the wiring harness? If yes, repair as necessary. If no, go to next step.
- The conditions that set the DTC are not present at this time. The following list may help in identifying the intermittent condition. With the engine running at normal operating temperature, monitor the DRBIII® parameters related to the DTC while wiggling the wiring harness. Look for parameter values to change and/or a DTC to set. Review the DRBIII® Freeze Frame information. If possible, try to duplicate the conditions under which the DTC was set. Turn the ignition off. Refer to any Technical Service Bulletins (TSB) that may apply. Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or partially broken wires. Visually inspect the related wiring harness connectors. Look for broken, bent, pushed out, or corroded terminals. Were any of the above conditions present? If yes, repair as necessary. If no, test is complete.
- Turn the ignition off. Remove the High Speed Radiator Fan Relay from the PDC. Turn the ignition on. Measure the voltage of the Fused Ignition Switch Output circuit in the PDC. Is the voltage above 11.0 volts? If yes, go to next step. If no, repair the Fused Ignition Switch Output circuit. Check and replace any open fuses.
- Turn the ignition off. Measure the resistance of the High Speed Radiator Fan Relay between the Fused Ignition Switch Output terminal and the High Speed Radiator Fan Relay Control terminal. Is the resistance between 60 to 80 ohms? If yes, go to next step. If no, replace the High Speed Radiator Fan Relay.
- Ensure the ignition is off. Disconnect the PCM harness connectors. Measure the resistance of the High Speed Radiator Fan Relay Control circuit between the PDC and the PCM harness connector. Is the resistance below 5.0 ohms? If yes, go to next step. If no, repair the High Speed Radiator Fan Relay Control circuit for an open.
- Measure the resistance of the High Speed Radiator Fan Relay Control circuit in the PDC to ground. Is the resistance below 5.0 ohms? If yes, repair the High Speed Radiator Fan Relay Control circuit for a short to ground. If no, go to next step.
- There are no possible causes remaining, replace PCM. Program the new PCM. See PROGRAMMING .
WARNING:
When the engine is operating, do not stand in a direct line with the fan. Do not put your hands near the pulleys, belts or fan. Do not wear loose clothing.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.