Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2000 Chrysler Intrepid BaseFACTORY OEM SERVICE PROCEDURE
Specifications Index
CONCORDE, INTREPID, LHS & 300M SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning - Automatic System | |||
| Service | SPECIFICATIONS | ||
| Torque | N/A | ||
| Air Conditioning - Manual System | |||
| Service | SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front Driveshaft Nut (Except LHS) | 105 Ft. Lbs. (150 N.m) | ||
| Front Driveshaft Nut (LHS) | 120 Ft. Lbs. (163 N.m) | ||
| Rear Spindle Retaining Nut | 124 Ft. Lbs. (168 N.m) | ||
| Brakes | |||
| Bleeding Sequence | |||
| Without ABS | BLEEDING PROCEDURE | ||
| With ABS | BLEEDING BRAKE SYSTEM | ||
| Disc Brakes | DISC BRAKE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Charging | |||
| Generator | ON-VEHICLE TESTING | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | BELT ADJUSTMENT | ||
| Belt Routing | DRIVE BELT ROUTING | ||
| Engine Cooling | |||
| Service Specifications | COOLING SYSTEM SPECIFICATIONS | ||
| Pressure Cap Pressure | 16 PSI | ||
| Water Pump R & I | WATER PUMP | ||
| Engine Mechanical (3.2L & 3.5L) | |||
| Compression | ENGINE COMPRESSION | ||
| Oil Pressure | Oil pressure is 5 psi (0.35 kg/cm2 ) at idle, and 45-105 psi (3.1-7.3 kg/cm2 ) at 3000 RPM. | ||
| Overhaul | ENGINE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Drive Plate/Flexplate Torque | 70 Ft. Lbs. (95 N.m) | ||
| Fuel System | |||
| Fuel Filter Location | Fuel filter is incorporated into the fuel pressure regulator. A separate frame mounted fuel filter is not used. Refer to FUEL FILTER/FUEL PRESSURE REGULATOR . | ||
| Pressure Specification | FUEL PUMP | ||
| Fuel Pressure Test Procedure | FUEL PRESSURE TEST | ||
| Fuel Pressure Release Procedure | FUEL PRESSURE RELEASE | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | HIGH TENSION WIRE RESISTANCE | ||
| Ignition Wires (Routing) | FIRING ORDER & TIMING MARKS . Wire routing is located in Figures. | ||
| Spark Plugs | SPARK PLUGS | ||
| Starting | |||
| Starter | STARTER SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel & Tire | |||
| Lug Nut Torque | 100 Ft. Lbs. (135 N.m) Tighten nuts in crisscross sequence to half torque, then tighten to full torque. | ||
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.