Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHRYSLER1993LEBARON LANDAUREPAIR AND DIAGNOSIS (SINGLE PAGE)BODY & FRAMEBODY, CAB CONTROL SYSTEMSTRAVELER MODULE
1993 Chrysler LeBaron Landau
Traveler Module
1993 Chrysler LeBaron LandauSECTION Traveler Module
- Description & Operation
- Self-Diagnostic Tests
- Diagnostic Charts
- Test 1A - Identifying Traveler Problems
- Test 1B - Traveler No Response Message Or Blank Screen Problem
- Test 1C - Traveler Elapsed Time (ET) Problem
- Test 1D - Communication Problem
- Test 2A - Traveler Illumination Problem
- Test 2B - Diagnosing Headlight On Input To Traveler
- Test 2C - Diagnosing Panel Light Level Input To Traveler
- Test 2D - Diagnosing Short CKT On Headlight CKT To Traveler
- Test 3A - Diagnosing Fuel Level Sense Circuit To Traveler
- Test 3B - Fuel Gauge Problem
- Test 3C - Short In Fuel Gauge Circuit
- Test 3D - Diagnosing Sending Unit/Fuel Gauge For Calibration
- Test 4A - Traveler Button Problem
- Test 5A - Electronic Instrument Cluster Fuel Gauge Problem
- Test 5B - Electronic Instrument Cluster Shorted Fuel Gauge Circuit
- Test 6A - Vacuum Fluorescent Display Problem
- Verification Procedure VER-1 - Verification Of Repairs
- Vehicle Communications Tests
- Notes
- Test 1A - Fault Messages
- Test 2A - Blank DRB-II Message Screen
- Test 3A - Ram Test Failure
- Test 4A - Cartridge Error
- Test 5A - Key Pad Test Failure
- Test 6A - Low Or High Battery
- Test 7A - Short To Battery
- Test 7B - Short To Battery
- Test 7D - Short To Battery
- Test 7E - Short To Battery
- Test 7F - Short To Battery
- Test 8A - Short To 5 Volts
- Test 8B - Short To 5 Volts
- Test 8D - Short To 5 Volts
- Test 8E - Short To 5 Volts
- Test 8G - Short To 5 Volts
- Test 9A - Short To Ground
- Test 10A - Bus (+) & Bus (-) Shorted Together
- Test 11A - No Termination
- Test 11B - No Termination
- Test 12A - Bus Bias Level Or Bus (+/-) Open
- Test 12B - Bus Bias Level Or Bus (+/-) Open
- Test 12G - Bus Bias Level Or Bus (+/-) Open
- Test 13A - No Bus Bias
- Test 13B - No Bus Bias
- Test 13K - No Bus Bias
- Test 14A - Not Receiving Bus Messages Correctly
- Verification Procedure VER-1
- Connector Identification
- Wiring Diagram
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.