Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Installation Procedure
Communication Interface Module Bracket (2) - Install
- Communication Interface Module Bracket Bolt (1) - Install and tighten [2x] - Fastener Specifications
- NOTE:
When reconnecting the module, the BROWN J2 connector must be connected last. Once all the parts are all in place, check and clear all DTCs in the heater and air conditioning remote control.
{If equipped} Heater and Air Conditioning Remote Control (2) - Install
- {If equipped} Seat the heater and air conditioning remote control until the detent (1) on the communication interface module bracket locks.
Serial Data Gateway Module (1) - Install
- Secure the retaining tabs.
Communication Interface Module (1) - Install
- Secure the retaining tabs.
Instrument Panel Tie Bar (1) - Install
- Attach the wiring harness and connect the electrical connectors as necessary.
- Remove the support supporting the heater and air conditioning evaporator and blower module.
Instrument Panel Wiring Harness Ground Nut (2) - Install and tighten [2x] - Fastener Specifications
- Connect the instrument panel wiring harness (1) clip and connector.
- NOTE:
Some components not shown for graphic clarity.
Heater and Air Conditioning Evaporator and Blower Module Bolt (1) @ Heater and Air Conditioning Evaporator and Blower Module - Install and tighten [5x] - Fastener Specifications
Instrument Panel Tie Bar Bolt (1) @ Plenum Lower Panel - Install and tighten [2x] - Fastener Specifications
Instrument Panel Tie Bar Bolt (2) @ Front Side Door - Install and tighten [2x] - Fastener Specifications
- Body Hinge Pillar Outer Panel Hole Plug (1) - Install [2x]
Instrument Panel Tie Bar Bolt (2) @ Front Side Door - Install and tighten [2x] - Fastener Specifications
- Body Hinge Pillar Outer Panel Hole Plug (1) - Install [2x]
Instrument Panel Tie Bar Bolt (1) @ Floor Panel Tunnel Panel - Install and tighten [2x] - Fastener Specifications
Data Link Connector (2) - Install
- Data Link Connector Bolt (1) - Install and tighten [2x] - Fastener Specifications
Instrument Panel Tie Bar Bolt (1) - Install and tighten - Fastener Specifications
- Use a suitable tool to push the tab (2) in the up position.
Heater and Air Conditioning Evaporator and Blower Module Bolt (1) - Install and tighten - Fastener Specifications
- Use a suitable tool to push the tab (2) in the up position.
- Instrument Panel Tie Bar Bolt (3) - Install and tighten - Fastener Specifications
Connect the instrument panel wiring harness connectors (2) to the high frequency antenna harness.
- Instrument Panel Wiring Harness Retainer (1) - Install [2x]
Instrument Panel Carrier (1) - Install - Instrument Panel Carrier Replacement (WT, Custom) , or Instrument Panel Carrier Replacement (without Front Floor Console) , or Instrument Panel Carrier Replacement (with Front Floor Console)
{If equipped} Instrument Panel Lower Trim Panel Insulator - Right Side (1) - Install
{If equipped} Instrument Panel Lower Insulator Retainer (1) - Install [3x]
Starting at the front of the front side door sill garnish molding (1) engage the 2 retaining clips on the forward vertical wall.
- Work your way rearward engaging the front side door sill garnish molding retaining clips.
- Front Side Door Sill Garnish Molding - Left Side and Right Side (1) - Install [2x]
Windshield Wiper System Module Shield (1) - Install
Air Inlet Grille Panel (2) - Install
- Connect the windshield washer nozzle hose to the windshield washer pump hose.
- Air Inlet Grille Panel Retainer (1) - Install [8x]
Hood Rear Outer Air Inlet Seal (2) - Install [2x]
- Air Inlet Grille Panel Retainer (1) - Install [2x]
Air Inlet Grille Panel Extension - Left Side (1) - Install
- Remove the double layer of masking tape around the perimeter of the painted surfaces.
- Using a 50/50 mixture of isopropyl alcohol and clean drinkable water with a clean towel, remove any left over adhesive residue from the masking tape.
- NOTE:
Some components not shown for graphic clarity.
Air Inlet Grille Panel Extension - Right Side (1) - Install
- Remove the double layer of masking tape around the perimeter of the painted surfaces.
- Using a 50/50 mixture of isopropyl alcohol and clean drinkable water with a clean towel, remove any left over adhesive residue from the masking tape.
Radio Antenna (1) - Install
- Rotate the antenna clockwise to secure the radio antenna to the antenna base.
Clean the left and right side windshield wiper transmission pivot shaft splines with a soft wire brush before installing the windshield wiper arm (3).
- Position the windshield wiper arms (3) on the windshield wiper transmission pivot shafts.
- Windshield Wiper Arm Nut (2) - Install and tighten - Fastener Specifications
- Windshield Wiper Arm Finish Cap (1) - Install [2x]
If required, realign the windshield wipers to their respective alignment circles (1) on the windshield.
- Lubricate the windshield with clean washer fluid.
- Run the windshield wipers for two complete cycles then turn off the windshield wipers.
- Ensure the windshield wipers are in the full park position.
Refer to Fastener Caution .
NO RELATED
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.