Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2023MALIBU LTREPAIR AND DIAGNOSISENGINE MECHANICALSTARTER12 V BATTERY, STARTING AND CHARGING - SPECIFICATIONSSPECIFICATIONSFASTENER SPECIFICATIONS
2023 Chevrolet Malibu LT
Fastener Specifications
2023 Chevrolet Malibu LTSECTION Fastener Specifications
Reusable Threaded Fastener Tightening Specifications
|
NOTE:
All fasteners listed in this table can be reused after removal. |
|
|---|---|
| Application | Specification |
| Metric (English) | |
| Auxiliary Battery Positive Cable Fastener @ Engine Wiring Harness Junction Block | 16 N.m (12 lb ft) |
| Battery Hold Down Bolt (Lower Bolt) | 22 N.m (16 lb ft) |
| Battery Hold Down Bolt (Upper Retainer Bolt) | 9 N.m (80 lb in) |
| Battery Hold Down Nut (Upper Retainer Nut) | 9 N.m (80 lb in) |
| Battery Negative Cable Ground Bolt @ Transmission (LFV) | 40 N.m (30 lb ft) |
| Battery Negative Cable Ground Nut @ Frame Rail | 9 N.m (80 lb in) |
| Battery Negative Cable Nut @ Battery Sensor | 9 N.m (80 lb in) |
| Battery Positive Cable Bolt @ High Voltage Battery (HP4) | 22 N.m (16 lb ft) |
| Battery Positive Cable Nut @ Battery Distribution Fuse Block (HP4) | 16 N.m (12 lb ft) |
| Battery Positive Cable Nut @ Generator (LFV) | 15 N.m (11 lb ft) |
| Battery Positive Cable Nut @ Engine Wiring Harness Junction Block | 16 N.m (12 lb ft) |
| Battery Positive Cable Nut @ Starter Solenoid (LFV) | 13 N.m (115 lb in) |
| Battery Positive Post Clamp Nut | 9 N.m (80 lb in) |
| Battery Post Negative Cable Clamp Nut | 9 N.m (80 lb in) |
| Battery Tray Mounting Bolt | 22 N.m (16 lb ft) |
| Battery Tray Mounting Nut | 22 N.m (16 lb ft) |
| Battery Tray Support Bolt | 22 N.m (16 lb ft) |
| Body Harness Ground Fastener @ Battery Negative Post (Without KL9) | 9 N.m (80 lb in) |
| Body Harness Ground Fastener @ Battery Sensor | 9 N.m (80 lb in) |
| Engine Wiring Harness Fuse Block Bracket Bolt | 9 N.m (80 lb in) |
| Fuse Block Bracket Bolt | 9 N.m (80 lb in) |
| Generator Bolt (LFV) | 22 N.m (16 lb ft) |
| Generator Nut (LFV) | 22 N.m (16 lb ft) |
| Generator Mounting Stud (LFV) | 9 N.m (80 lb in) |
| Multifunction Power Supply Converter Bracket Nut | 6 N.m (53 lb in) |
| Starter Bracket Large Bolt (LFV) | 58 N.m (43 lb ft) |
| Starter Bracket Small Bolt (LFV) | 22 N.m (16 lb ft) |
| Starter Mounting Bolt (LFV) | 58 N.m (43 lb ft) |
| Starter Mounting Nut (LFV) | 58 N.m (43 lb ft) |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.