SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2022TRAX LT, AWDREPAIR AND DIAGNOSISBODY & FRAMEFIXED AND MOVEABLE WINDOWSDIAGNOSTIC INFORMATION AND PROCEDURESREAR WINDOW DEFOGGER MALFUNCTION (ENCORE)CIRCUIT/SYSTEM TESTING
2022 Chevrolet Trax LT, AWD

Circuit/System Testing

2022 Chevrolet Trax LT, AWDSECTION Circuit/System Testing
    NOTE:

    It may take up to 2 min for all vehicle systems to power down before an accurate ground or low reference circuit continuity test can be performed.

  1. Ignition/Vehicle & All vehicle systems - Off
  2. Disconnect the electrical connector: X1 & X2 @ E18 Rear Defogger Grid
  3. Test for less than 10 ohms between the test points: Ground circuit terminal 1 X2 & Ground
    • If 10 ohms or greater 
    1. Ground Connection - Disconnect
    2. Test for less than 2 ohms between the test points: Ground circuit terminal 1 X2 @ Component harness & Ground Connection
      • If 2 ohms or greater - Repair the open/high resistance in the circuit.
      • If less than 2 ohms - Repair the open/high resistance in the ground connection.
    • Go to next step: If less than 10 ohms 
  4. Verify the fuse is not open: F12UA Fuse
    • If the fuse is open 
    1. Replace the component: F12UA Fuse
    2. Verify the fuse does not open.
      • If the fuse opens - Test or replace the component: X50A Fuse Block - Underhood
      • If the fuse does not open, go to the next step.
    • Go to next step: If the fuse is not open 
  5. Connect a test lamp between the test points: Control circuit terminal 1 X1 & Ground circuit terminal 1 X2
  6. Ignition - On / Vehicle - In Service Mode
  7. Operate the component: Rear Defogger Switch - Pressed

    Verify the test lamp does not turn On and Off.

    • If the test lamp turns On and Off 

      Test or replace the component: E18 Rear Defogger Grid

    • Go to next step: If the test lamp does not turn On and Off 
  8. Ignition/Vehicle - Off
  9. Connect the electrical connector: X1 & X2 @ E18 Rear Defogger Grid
  10. Disconnect the electrical connector: X2 @ X50A Fuse Block - Underhood
  11. Ignition - On / Vehicle - In Service Mode
  12. Momentarily connect a 25 A fused jumper wire between the test points: Control circuit terminal A3 X2 & B+

    Verify the component turns On and Off when connecting and disconnecting the jumper wire: E18 Rear Defogger Grid

    • If the component does not turn On and Off 
    1. Ignition/Vehicle - Off & Remove - Jumper wire (s)
    2. Disconnect the electrical connector: X1 @ E18 Rear Defogger Grid
    3. Ignition - On / Vehicle - In Service Mode
    4. Test for less than 1 V between the test points: Control circuit terminal 1 X1 @ Component harness & Ground
      • If 1 V or greater - Repair the short to voltage on the circuit.
      • Go to next step: If less than 1 V
    5. Ignition/Vehicle - Off
    6. Test for infinite resistance between the test points: Control circuit terminal 1 X1 @ Component harness & Ground
      • If less than infinite resistance - Repair the short to ground on the circuit.
      • Go to next step: If infinite resistance
    7. Test for less than 2 ohms between the test points: Control circuit terminal 1 X1 @ Component harness & Terminal A3 X2 @ Fuse Block Harness
      • If 2 ohms or greater - Repair the open/high resistance in the circuit.
      • If less than 2 ohms - Test or replace the component: E18 Rear Defogger Grid
    • Go to next step: If the component turns On and Off 
  13. Ignition/Vehicle & All vehicle systems - Off
  14. Verify the fuse is not open: F12UA Fuse
    • If the fuse is open 

      Test or replace the component: X50A Fuse Block - Underhood

    • Go to next step: If the fuse is not open 
  15. Test for less than 10 ohms between the test points: Ground circuit terminal C5 X2 & Ground
    • If 10 ohms or greater 
    1. Ground Connection - Disconnect
    2. Test for less than 2 ohms between the test points: Ground circuit terminal C5 X2 & Ground Connection
      • If 2 ohms or greater - Repair the open/high resistance in the circuit.
      • If less than 2 ohms - Repair the open/high resistance in the ground connection.
    • Go to next step: If less than 10 ohms 
  16. Connect the electrical connector: X2 @ X50A Fuse Block - Underhood
  17. Disconnect the electrical connector: X2 @ K33 HVAC Control Module
  18. Ignition - On / Vehicle - In Service Mode
  19. Momentarily connect a 3 A fused jumper wire between the test points: Control circuit terminal 19 X2 & B+

    Verify the component turns On and Off when connecting and disconnecting the jumper wire: E18 Rear Defogger Grid

    • If the component does not turn On and Off 
    1. Ignition/Vehicle - Off & Remove - Jumper wire (s)
    2. Disconnect the electrical connector: X2 @ X50A Fuse Block - Underhood
    3. Ignition - On / Vehicle - In Service Mode
    4. Test for less than 1 V between the test points: Control circuit terminal 19 X2 @ Control module harness & Ground
      • If 1 V or greater - Repair the short to voltage on the circuit.
      • Go to next step: If less than 1 V
    5. Ignition/Vehicle - Off
    6. Test for infinite resistance between the test points: Control circuit terminal 19 X2 @ Control module harness & Ground
      • If less than infinite resistance - Repair the short to ground on the circuit.
      • Go to next step: If infinite resistance
    7. Test for less than 2 ohms between the test points: Control circuit terminal 19 X2 @ Control module harness & Terminal B1 X2 @ Fuse Block Harness
      • If 2 ohms or greater - Repair the open/high resistance in the circuit.
      • If less than 2 ohms - Test or replace the component: X50A Fuse Block - Underhood
    • Go to next step: If the component turns On and Off 
  20. Replace the component: K33 HVAC Control Module
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.