SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2022TRAX LT, AWDREPAIR AND DIAGNOSIS (SINGLE PAGE)ACCESSORIES & EQUIPMENTANTI-THEFT SYSTEMSVEHICLE ACCESS SYSTEMDIAGNOSTIC INFORMATION AND PROCEDURESPOWER DOOR LOCK KEY CYLINDER SWITCHES MALFUNCTIONCIRCUIT/SYSTEM TESTING
2022 Chevrolet Trax LT, AWD

Circuit/System Testing

2022 Chevrolet Trax LT, AWDSECTION Circuit/System Testing
    NOTE:

    It may take up to 2 min for all vehicle systems to power down before an accurate ground or low reference circuit continuity test can be performed.

  1. Ignition/Vehicle & All vehicle systems - Off
  2. Disconnect the electrical connector: A23D Door Latch Assembly - Driver
  3. Test for less than 10 ohms between the test points: Ground circuit terminal 8 & Ground
    • If 10 ohms or greater 
    1. Ground Connection - Disconnect
    2. Test for less than 2 ohms between the test points: Ground circuit terminal 8 @ Component harness & Ground Connection
      • If 2 ohms or greater - Repair the open/high resistance in the circuit.
      • If less than 2 ohms - Repair the open/high resistance in the ground connection.
    • Go to next step: If less than 10 ohms 
  4. Connect the electrical connector: A23D Door Latch Assembly - Driver
  5. Disconnect the electrical connector: S79D Window Switch - Driver
  6. Connect a test lamp between the test points: Signal circuit terminal 7 & B+
  7. Operate the component: B29D Door Lock Key Cylinder Switch - Driver - Lock & Unlock

    Verify the test lamp turns On and Off.

    • If the test lamp is always Off 
    1. Ignition/Vehicle - Off & Remove - Test lamp
    2. Disconnect the electrical connector: A23D Door Latch Assembly - Driver
    3. Ignition - On/Vehicle - In Service Mode
    4. Test for less than 1 V between the test points: Signal circuit terminal 7 @ Component harness & Ground
      • If 1 V or greater - Repair the short to voltage on the circuit.
      • Go to next step: If less than 1 V
    5. Ignition/Vehicle - Off
    6. Test for less than 2 ohms between the test points: Signal circuit terminal 7 @ Component harness & Terminal 4 @ A23D Door Latch Assembly - Driver
      • If 2 ohms or greater - Repair the open/high resistance in the circuit.
      • If less than 2 ohms - Replace the component: A23D Door Latch Assembly - Driver
    • If the test lamp is always On 
    1. Ignition/Vehicle - Off & Remove - Test lamp
    2. Disconnect the electrical connector: A23D Door Latch Assembly - Driver
    3. Test for infinite resistance between the test points: Signal circuit terminal 7 @ Component harness & Ground
      • If less than infinite resistance - Repair the short to ground on the circuit.
      • If infinite resistance - Replace the component: A23D Door Latch Assembly - Driver
    • Go to next step: If the test lamp turns On and Off 
  8. Test or replace the component: S79D Window Switch - Driver
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.