SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2019TRAX PREMIER, AWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 99 (POWER DOOR LOCK SYSTEM AND RELEASE SYSTEMS)DIAGNOSTIC INFORMATION AND PROCEDURESPOWER DOOR LOCKS MALFUNCTIONCIRCUIT/SYSTEM TESTING
2019 Chevrolet Trax Premier, AWD

Circuit/System Testing

2019 Chevrolet Trax Premier, AWDSECTION Circuit/System Testing
WARNING: This page is about a different car, the 2018 Chevrolet Trax and 2018 Buick Encore. However, it is still accessible from the selected car via links, so may be relevant.

Test 1

    NOTE:

    It may take up to 2 min for all vehicle systems to power down before an accurate ground or low reference circuit continuity test can be performed.

  1. Ignition/Vehicle & All vehicle systems - Off
  2. Disconnect the appropriate electrical connector: S13D Door Lock Switch - Driver/S13P Door Lock Switch - Passenger
  3. Test for less than 10 ohms between the test points: Ground circuit terminal 3 & Ground
    • If 10 ohms or greater 
    1. Ground Connection - Disconnect
    2. Test for less than 2 ohms between the test points: Ground circuit terminal 3@Component harness & Ground Connection
      • If 2 ohms or greater - Repair the open/high resistance in the circuit.
      • If less than 2 ohms - Repair the open/high resistance in the ground connection.
    • Go to next step: If less than 10 ohms 
  4. Ignition - On / Vehicle - In Service Mode
  5. Verify the scan tool parameter: Driver Door Lock Switch or Passenger Door Lock Switch = Inactive
    • If not the specified state 
    1. Ignition/Vehicle - Off
    2. Disconnect the electrical connector: X1/X2/X7@K9 Body Control Module
    3. Test for infinite resistance between the test points:
      • Signal circuit terminal 2@Component harness & Ground
      • Signal circuit terminal 4@Component harness & Ground
      • If less than infinite resistance - Repair the short to ground on the circuit.
      • If infinite resistance - Replace the component: K9 Body Control Module
    • Go to next step: If the specified state 
  6. Connect a 3 A fused jumper wire between the test points: Signal circuit terminal 2 & Ground circuit terminal 3
  7. Verify the scan tool parameter: Driver Door Lock Switch or Passenger Door Lock Switch = Unlock
    • If not the specified state 
    1. Ignition/Vehicle - Off & Remove - Jumper wire(s)
    2. Disconnect the electrical connector: X1 or X2@K9 Body Control Module
    3. Ignition - On / Vehicle - In Service Mode
    4. Test for less than 1 V between the test points: Signal circuit terminal 2@Component harness & Ground
      • If 1 V or greater - Repair the short to voltage on the circuit.
      • Go to next step: If less than 1 V
    5. Ignition/Vehicle - Off
    6. Test for less than 2 ohms between the test points:
      • Signal circuit terminal 2@S13D Door Lock Switch - Driver & Terminal 15 X2@Control module harness
      • Signal circuit terminal 2@S13P Door Lock Switch - Passenger & Terminal 14 X1@Control module harness
      • If 2 ohms or greater - Repair the open/high resistance in the circuit.
      • If less than 2 ohms - Replace the component: K9 Body Control Module
    • Go to next step: If the specified state 
  8. Connect a 3 A fused jumper wire between the test points: Signal circuit terminal 4 & Ground circuit terminal 3
  9. Verify the scan tool parameter: Driver Door Lock Switch or Passenger Door Lock Switch = Lock
    • If not the specified state 
    1. Ignition/Vehicle - Off & Remove - Jumper wire(s)
    2. Disconnect the electrical connector: X2 or X7@K9 Body Control Module
    3. Ignition - On / Vehicle - In Service Mode
    4. Test for less than 1 V between the test points: Signal circuit terminal 4@Component harness & Ground
      • If 1 V or greater - Repair the short to voltage on the circuit.
      • Go to next step: If less than 1 V
    5. Ignition/Vehicle - Off
    6. Test for less than 2 ohms between the test points:
      • Signal circuit terminal 4@S13D Door Lock Switch - Driver & Terminal 19 X2@Control module harness
      • Signal circuit terminal 4@S13P Door Lock Switch - Passenger & Terminal 14 X7@Control module harness
      • If 2 ohms or greater - Repair the open/high resistance in the circuit.
      • If less than 2 ohms - Replace the component: K9 Body Control Module
    • Go to next step: If the specified state 
  10. Test or replace the component: S13D Door Lock Switch - Driver/S13P Door Lock Switch - Passenger

Test 2

  1. Ignition/Vehicle - Off
  2. Disconnect the electrical connector: A23D Door Latch Assembly - Driver
  3. Connect a test lamp between the test points: Control circuit terminal 2 & Control circuit terminal 3
  4. Ignition - On / Vehicle - In Service Mode
  5. Operate the component: S13D Door Lock Switch - Driver - Lock Switch & Unlock Switch

    Verify the test lamp does not turn On and Off.

    • If the test lamp turns On and Off 

      Test or replace the component: A23D Door Latch Assembly - Driver

    • Go to next step: If the test lamp does not turn On and Off 
  6. Ignition/Vehicle - Off
  7. Disconnect the electrical connector: X6@K9 Body Control Module
  8. Test for less than 2 ohms between the test points:
    • Control circuit terminal 3@A23D Door Latch Assembly - Driver & Terminal 1 X6@Control module harness
    • Control circuit terminal 2@A23D Door Latch Assembly - Driver & Terminal 4 X6@Control module harness
    • If 2 ohms or greater 
    • Repair the open/high resistance in the circuit.
    • Go to next step: If less than 2 ohms 
  9. Test or replace the component: K9 Body Control Module

Test 3

  1. Ignition/Vehicle & All vehicle systems - Off
  2. Disconnect the appropriate electrical connector:
    • A23LR Door Latch Assembly - Left Rear
    • A23P Door Latch Assembly - Passenger
    • A23RR Door Latch Assembly - Right Rear
  3. Connect a test lamp between the test points:
    • A23P Door Latch Assembly - Passenger Control circuit terminal 7 & Control circuit terminal 8
    • A23LR Door Latch Assembly - Left Rear Control circuit terminal 2 & Control circuit terminal 3
    • A23RR Door Latch Assembly - Right Rear Control circuit terminal 7 & Control circuit terminal 8
  4. Ignition - On / Vehicle - In Service Mode
  5. Operate the component: S13D Door Lock Switch - Driver - Lock Switch & Unlock Switch

    Verify the test lamp does not turn On and Off.

    • If the test lamp turns On and Off 

      Test or replace the component: A23 Door Latch Assembly

    • Go to next step: If the test lamp does not turn On and Off 
  6. Ignition/Vehicle - Off
  7. Disconnect the electrical connector: X6@K9 Body Control Module
  8. Ignition - On / Vehicle - In Service Mode
  9. Test for less than 2 ohms between the test points:
    • Control circuit terminal 3@A23LR Door Latch Assembly - Left Rear & Terminal 2 X6@Control module harness
    • Control circuit terminal 2@A23LR Door Latch Assembly - Left Rear & Terminal 4 X6@Control module harness
    • Control circuit terminal 7@A23P Door Latch Assembly - Passenger & Terminal 4 X6@Control module harness
    • Control circuit terminal 8@A23P Door Latch Assembly - Passenger & Terminal 2 X6@Control module harness
    • Control circuit terminal 7@A23RR Door Latch Assembly - Right Rear & Terminal 4 X6@Control module harness
    • Control circuit terminal 8@A23RR Door Latch Assembly - Right Rear & Terminal 2 X6@Control module harness
    • If 2 ohms or greater 
    • Repair the open/high resistance in the circuit.
    • Go to next step: If less than 2 ohms 
  10. Test or replace the component:K9 Body Control Module

Test 4

    NOTE:

    It may take up to 2 min for all vehicle systems to power down before an accurate ground or low reference circuit continuity test can be performed.

  1. Ignition/Vehicle & All vehicle systems - Off
  2. Disconnect the electrical connector: X2 & X6@K9 Body Control Module
  3. Test for less than 10 ohms between the test points: Ground circuit terminal 3 X6 & Ground
    • If 10 ohms or greater 
    1. Ground Connection - Disconnect
    2. Test for less than 2 ohms between the test points: Ground circuit terminal 3 X6 & Ground Connection
      • If 2 ohms or greater - Repair the open/high resistance in the circuit.
      • If less than 2 ohms - Repair the open/high resistance in the ground connection.
    • Go to next step: If less than 10 ohms 
  4. Ignition - On / Vehicle - In Service Mode
  5. Verify a test lamp turns On between the test points: B+ circuit terminal 4 X2 & Ground
    • If the test lamp does not turn On and the circuit fuse is OK 
    1. Ignition/Vehicle - Off & Remove - Test lamp
    2. Test for less than 2 ohms between the test points: B+ circuit terminal 4 X2 & Output terminal @Fuse
      • If 2 ohms or greater - Repair the open/high resistance in the circuit.
      • If less than 2 ohms - Verify the fuse is OK and there is voltage at the fuse.
    • If the test lamp does not turn On and the circuit fuse is open 
    1. Ignition/Vehicle - Off & Remove - Test lamp
    2. Disconnect the electrical connector:
      • A23D Door Latch Assembly - Driver
      • A23LR Door Latch Assembly - Left Rear
      • A23P Door Latch Assembly - Passenger
      • A23RR Door Latch Assembly - Right Rear
    3. Test for infinite resistance between the test points:
      • Control circuit terminal 1 X6@K9 Body Control Module & Ground
      • Control circuit terminal 2 X6@K9 Body Control Module & Ground
      • Control circuit terminal 4 X6@K9 Body Control Module & Ground
      • If less than infinite resistance - Repair the short to ground on the circuit.
      • If infinite resistance - Replace the component: A23 Door Latch Assembly
    • Go to next step: If the test lamp turns On 
  6. Ignition/Vehicle - Off
  7. Connect the electrical connector: X2@K9 Body Control Module
  8. Ignition - On / Vehicle - In Service Mode
  9. Test for less than 1 V between the test points:
    • Control circuit terminal 1 X6@K9 Body Control Module & Ground
    • Control circuit terminal 2 X6@K9 Body Control Module & Ground
    • Control circuit terminal 4 X6@K9 Body Control Module & Ground
    • If greater than 1 V 

      Repair the short to voltage on the circuit.

    • Go to next step: If 1 V or less 
  10. Ignition/Vehicle - Off
  11. Test for infinite resistance between the test points:
    • Control circuit terminal 1 X6@K9 Body Control Module & Ground
    • Control circuit terminal 2 X6@K9 Body Control Module & Ground
    • Control circuit terminal 4 X6@K9 Body Control Module & Ground
    • If less than infinite resistance 

      Repair the short to ground on the circuit.

    • Go to next step: If infinite resistance 
  12. Replace the component: K9 Body Control Module
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.