SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2019TRAX PREMIER, AWDREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 92 (DRIVER ASSISTANCE SYSTEMS)DIAGNOSTIC INFORMATION AND PROCEDURESDTC B094D OR B094ECIRCUIT/SYSTEM TESTING
2019 Chevrolet Trax Premier, AWD

Circuit/System Testing

2019 Chevrolet Trax Premier, AWDSECTION Circuit/System Testing
WARNING: This page is about a different car, the 2018 Chevrolet Trax and 2018 Buick Encore. However, it is still accessible from the selected car via links, so may be relevant.
    NOTE:

    Make sure to use a high impedance test lamp like special tool EL-35616-210.

  1. Ignition OFF and all vehicle systems OFF, disconnect the harness connector for the appropriate A9 Outside Rearview Mirror. It may take up to 2 min for all vehicle systems to power down.
    • A9A Outside Rearview Mirror - Driver
    • A9B Outside Rearview Mirror - Passenger
  2. Test for less than 10 Ω between the ground circuit terminal 9 (without AAG) or 12 (with AAG) and ground.
    • If 10 Ω or greater 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • If less than 10 Ω 
  3. Ignition ON, connect a test lamp between the control circuit terminal 8 (without AAG) or 11 (with AAG) and the ground circuit terminal 9 (without AAG) or 12 (with AAG).
  4. Verify the test lamp turns ON and OFF when commanding the Object Detection Alert Indicators On and Off with a scan tool.
    • If the test lamp is always OFF 
    1. Ignition OFF, disconnect the harness connector at the B218R Side Object Sensor Module - Right.
    2. Test for infinite resistance between the control circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • Go to next step: If infinite resistance
    3. Test for less than 2 Ω in the control circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the B218R Side Object Sensor Module - Right.
    • If the test lamp is always ON 
    1. Ignition OFF, disconnect the harness connector at the B218R Side Object Sensor Module - Right, ignition ON.
    2. Test for less than 1 V between the control circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the B218R Side Object Sensor Module - Right.
    • Go to next step: If the test lamp turns ON and OFF 
  5. Test or replace the A9 Outside Rearview Mirror Glass.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.