Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2019SILVERADO 1500 SSV, 4WD, GASREPAIR AND DIAGNOSISELECTRICALMOTORS, SWITCHES, RELAYSWIRING SYSTEMS AND POWER MANAGEMENT - SPECIFICATIONSSPECIFICATIONSFASTENER SPECIFICATIONS
2019 Chevrolet Silverado 1500 SSV, 4WD, Gas
Fastener Specifications
2019 Chevrolet Silverado 1500 SSV, 4WD, GasSECTION Fastener Specifications
Battery Distribution Engine Compartment Fuse Block (L3B)
| Callout | Component Name [Component Quantity] | Single Use Fastener / Component | Thread Locking Adhesive Required | Specification | Procedure Link |
|---|---|---|---|---|---|
| Metric (English) | |||||
| 1 | Battery Positive Cable Nut [2x] | - | - | 6 N.m (53 lb in) | Battery Distribution Engine Compartment Fuse Block Replacement (L3B) |
| 2 | Battery Positive Cable Nut [3x] | - | - | 15 N.m (11 lb ft) | Battery Distribution Engine Compartment Fuse Block Replacement (L3B) |
| 3 | Battery Positive Post Clamp Nut | - | - | 5 N.m (44 lb in) | Battery Distribution Engine Compartment Fuse Block Replacement (L3B) |
Battery Distribution Engine Compartment Fuse Block (L82, L84, L87, LV3)
| Callout | Component Name [Component Quantity] | Single Use Fastener / Component | Thread Locking Adhesive Required | Specification | Procedure Link |
|---|---|---|---|---|---|
| Metric (English) | |||||
| 1 | Battery Positive Cable Nut | - | - | 6 N.m (53 lb in) | Battery Distribution Engine Compartment Fuse Block Replacement (L82, L84, L87, LV3) |
| 2 | Battery Positive Cable Nut [3x] | - | - | 15 N.m (11 lb ft) | Battery Distribution Engine Compartment Fuse Block Replacement (L82, L84, L87, LV3) |
| 3 | Battery Positive Post Clamp Nut | - | - | 5 N.m (44 lb in) | Battery Distribution Engine Compartment Fuse Block Replacement (L82, L84, L87, LV3) |
Ignition Components
| Callout | Component Name [Component Quantity] | Single Use Fastener / Component | Thread Locking Adhesive Required | Specification | Procedure Link |
|---|---|---|---|---|---|
| Metric (English) | |||||
| 1 | Ignition and Start Switch Housing Bolt | Yes | - | Tighten until the bolt head breaks off. | Ignition and Start Switch Housing Replacement |
| 2 | Ignition and Start Switch Housing Bolt-Right Side | - | - | 2.5 N.m (22 lb in) | Ignition and Start Switch Housing Replacement |
| 3 | Ignition and Start Switch Housing Bolt-Left Side | - | - | 2.5 N.m (22 lb in) | Ignition and Start Switch Housing Replacement |
| 4 | Ignition and Start Switch Bolt [2x] | - | - | 1.8 N.m (16 lb in) | Ignition and Start Switch Replacement |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.