SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2019EXPRESS 2500 BASE, VAN CARGO EXTENDED, 6.0L ENG VIN GREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 35 (ANTILOCK BRAKE SYSTEM)DIAGNOSTIC INFORMATION AND PROCEDURESTRACTION CONTROL/STABILITY CONTROL INDICATOR MALFUNCTIONCIRCUIT/SYSTEM TESTING
2019 Chevrolet Express 2500 Base, Van Cargo Extended, 6.0L Eng VIN G

Circuit/System Testing

2019 Chevrolet Express 2500 Base, Van Cargo Extended, 6.0L Eng VIN GSECTION Circuit/System Testing
WARNING: This page is about a different car, the 2018 GMC Savana 3500, 2018 GMC Savana 2500, 2018 Chevrolet Express 3500, and 2018 Chevrolet Express 2500. However, it is still accessible from the selected car via links, so may be relevant.
NOTE:

Circuit/System Verification must be performed before Circuit/System Testing.

  1. Ignition OFF, disconnect the X1 harness connector at the S48A Multifunction Switch - Instrument Panel. It may take up to 2 min for all vehicle systems to power down.
  2. Test for less than 5 Ω between the ground circuit terminal 14 and ground.
    • If 5 Ω or greater 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • Go to next step: If less than 5 Ω 
  3. Ignition ON.
  4. Verify the scan tool Body Control Module Traction Control Switch parameter is Inactive.
    • If not Inactive 
    1. Ignition OFF, disconnect the X2 harness connector at the K9 Body Control Module.
    2. Test for infinite resistance between the signal circuit terminal 14 X2 and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the K9 Body Control Module.
    • Go to next step: If Inactive 
  5. Install a 3 A fused jumper wire between the signal circuit terminal 17 and the ground circuit terminal 14.
  6. Verify the scan tool Traction Control Switch parameter is Active.
    • If not Active 
    1. Ignition OFF, disconnect the X2 harness connector at the K9 Body Control Module, ignition ON.
    2. Test for less than 1 V between the signal circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • Go to next step: If less than 1 V.
    3. Test for less than 2 Ω in the signal circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K9 Body Control Module.
    • Go to next step: If Active 
  7. Test or replace the S48A Multifunction Switch - Instrument Panel.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.