SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2018TRAVERSE LS, 4WDREPAIR AND DIAGNOSISELECTRICALMOTORS, SWITCHES, RELAYSWIRING SYSTEMS AND POWER MANAGEMENT - DIAGNOSTIC INFORMATION AND PROCEDURESDIAGNOSTIC INFORMATION AND PROCEDURESDTC B144BCIRCUIT/SYSTEM TESTING
2018 Chevrolet Traverse LS, 4WD

Circuit/System Testing

2018 Chevrolet Traverse LS, 4WDSECTION Circuit/System Testing
  1. Ignition/Vehicle OFF, disconnect the X3 harness connector at the K9 Body Control Module.
  2. Test for less than 1 V between the ignition circuit terminal 6 and ground.
    • If 1 V or greater 

      Repair the short to voltage on the circuit.

    • Go to next step: If less than 1 V 
  3. Ignition ON/Vehicle in Service Mode.
  4. Verify a test lamp illuminates between the ignition circuit terminal 6 and ground.
    • If the test lamp does not illuminate 
    1. Ignition/Vehicle OFF, remove the test lamp.
    2. Test for infinite resistance between the ignition circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • Go to next step: If infinite resistance.
    3. Test for less than 2 Ω in the ignition circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K84 Keyless Entry Control Module.
    • Go to next step: If the test lamp illuminates 
  5. Ignition/Vehicle OFF, connect the X3 harness connector at the K9 Body Control Module.
  6. Disconnect the KR73 Ignition Main Relay. It may take up to 2 min for all vehicle systems to power down.
  7. Test for less than 10 Ω between the ground circuit terminal 86 and ground.
    • If 10 Ω or greater 
    1. Ignition/Vehicle OFF.
    2. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • Go to next step: If less than 10 Ω 
  8. Connect a test lamp between the control circuit terminal 85 and the ground circuit terminal 86.
  9. Verify the test lamp turns ON and OFF when commanding the Run/Crank Relay On and Off with a scan tool.
    • If the test lamp is always OFF 
    1. Ignition/Vehicle OFF, disconnect the harness connector at the K9 Body Control Module.
    2. Test for infinite resistance between the control circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • Go to next step: If infinite resistance.
    3. Test for less than 2 Ω in the control circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the K9 Body Control Module.
    • If the test lamp is always ON 
    1. Ignition/Vehicle OFF, disconnect the harness connector at the K9 Body Control Module, ignition ON/Vehicle in Service Mode.
    2. Test for less than 1 V between the control circuit and ground.
      • If 1 V or greater, repair the short to voltage on the circuit.
      • If less than 1 V, replace the K9 Body Control Module.
    • Go to next step: If the test lamp turns ON and OFF 
  10. Test or replace the KR73 Ignition Main Relay.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.