SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2018SILVERADO 2500 HD WT, 2D PICKUP, 6.0L ENG VIN G, RWD, GASREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 2134 (WIRING SYSTEMS AND POWER MANAGEMENT - COMPONENT CONNECTOR END VIEWS - ELECTRONIC STEERING CONTROL MODULE X2 THROUGH MEMORY SEAT MODULE)COMPONENT CONNECTOR END VIEWSMEMORY SEAT MODULE (MSM) X1 (AN3)
2018 Chevrolet Silverado 2500 HD WT, 2D Pickup, 6.0L Eng VIN G, RWD, Gas

Memory Seat Module (MSM) X1 (AN3)

2018 Chevrolet Silverado 2500 HD WT, 2D Pickup, 6.0L Eng VIN G, RWD, GasSECTION Memory Seat Module (MSM) X1 (AN3)
WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2011 GMC Yukon XL, 2011 GMC Yukon, 2011 Chevrolet Tahoe, 2011 Chevrolet Suburban, and 2011 Chevrolet Avalanche. However, it is still accessible from the selected car via links, so may be relevant.
Fig 1: Memory Seat Module (MSM) X1 (AN3) Connector End Views
GM1653404Courtesy of GENERAL MOTORS CORP.
Memory Seat Module (MSM) X1 (AN3)

Pin Wire Circuit Function
1 1 PU 2424 Ground (without KB6)
2-3 - - Not Used
4 1 L-BU 2433 Ground (without KB6)
1 OG 6194 Ground (KB6)
5 - - Not Used
6 1 D-BU 2479 Heated Seat Cushion Element Control (without KB6)
1 BN 6193 Heated Seat Cushion Element Control (KB6)
7-8 - - Not Used
9 1 TN 285 Driver Seat Horizontal Motor Forward Control
10 1 L-GN 284 Driver Seat Horizontal Motor Rearward Control
11 1 L-GN 2078 Ground (without KB6)
12 1 D-GN 286 Driver Seat Front Vertical Motor Up Control
13 1 D-BU 287 Driver Seat Front Vertical Motor Down Control
14 1 PK 2077 Heated Seat Cushion Element Control (without KB6)
15 1 YE 282 Driver Seat Rear Vertical Motor Up Control
16 1 L-BU 283 Driver Seat Rear Vertical Motor Down Control
Connector Part Information
  • Harness Type: Driver Seat
  • OEM Connector: 6098-4611
  • Service Connector: 15134091
  • Description: 16-Way F 1.5 Series (BK)
Terminal Part Information
  • Terminated Lead: 13327201
  • Release Tool: J-38125-553
  • Diagnostic Test Probe: J-35616-2A (GY)
  • Terminal/Tray: 8240-0128/22
  • Core/Insulation Crimp: C/A
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.