SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2016IMPALA LS, 3.6L ENG VIN NREPAIR AND DIAGNOSISENGINE PERFORMANCETESTING & DIAGNOSISDATA COMMUNICATION SYSTEMDIAGNOSTIC INFORMATION AND PROCEDURESDTC U0074: CONTROL MODULE COMMUNICATION POWERTRAIN EXPANSION CAN BUS OFF MALFUNCTIONCIRCUIT/SYSTEM TESTINGTESTING THE DEVICE CIRCUITS
2016 Chevrolet Impala LS, 3.6L Eng VIN N

Testing the Device Circuits

2016 Chevrolet Impala LS, 3.6L Eng VIN NSECTION Testing the Device Circuits
  1. Ignition OFF, all access doors closed, all vehicle systems OFF and all keys at least 3 meters (9.8 feet) away from vehicle. It may take up to 2 minutes for all vehicle systems to power down.
  2. Test for less than 10 Ω between each ground circuit terminal at the device that was just disconnected and ground.
    • If 10 Ω or greater 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the ground circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, repair the open/high resistance in the ground connection.
    • If less than 10 Ω 
  3. If equipped, verify a test lamp illuminates between each B+ circuit terminal and ground.
    • If the test lamp does not illuminate and the circuit fuse is good 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the B+ circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, verify the fuse is not open and there is voltage at the fuse.
    • If the test lamp does not illuminate and the circuit fuse is open 
    1. Ignition OFF.
    2. Test for infinite resistance between the B+ circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the disconnected device.
    • If the test lamp illuminates 
  4. Ignition ON.
  5. If equipped, verify a test lamp illuminates between each ignition circuit terminal, which has a fuse in the circuit and ground.
    • If the test lamp does not illuminate and the circuit fuse is good 
    1. Ignition OFF.
    2. Test for less than 2 Ω in the ignition circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, verify the fuse is OK and there is voltage at the fuse.
    • If the test lamp does not illuminate and the circuit fuse is open 
    1. Ignition OFF.
    2. Test for infinite resistance between the ignition circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance, replace the disconnected device.
    • If the test lamp illuminates 
  6. If equipped, verify a test lamp illuminates between each ignition circuit terminal, which is controlled by a control module and ground.
    • If the test lamp does not illuminate 
    1. Ignition OFF, disconnect the harness connectors at the control module that controls the ignition circuit.
    2. Test for infinite resistance between the ignition circuit and ground.
      • If less than infinite resistance, repair the short to ground on the circuit.
      • If infinite resistance
    3. Test for less than 2 Ω in the ignition circuit end to end.
      • If 2 Ω or greater, repair the open/high resistance in the circuit.
      • If less than 2 Ω, replace the control module that controls the ignition circuit.
    • If the test lamp illuminates 
  7. Replace the device that was disconnected.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.