Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2016IMPALA LS, 3.6L ENG VIN NREPAIR AND DIAGNOSISELECTRICALWIRING DIAGRAMSWIRING SYSTEMS AND POWER MANAGEMENT - COMPONENT CONNECTOR END VIEWS - B235 TO K9 X3COMPONENT CONNECTOR END VIEWSK9 BODY CONTROL MODULE X2
2016 Chevrolet Impala LS, 3.6L Eng VIN N
K9 Body Control Module X2
2016 Chevrolet Impala LS, 3.6L Eng VIN NSECTION K9 Body Control Module X2
Connector Part Information
|
Terminal Part Information
| Terminal Type ID | Terminated Lead | Diagnostic Test Probe | Terminal Removal Tool | Service Terminal | Tray Name | Core Crimp | Insulation Crimp |
|---|---|---|---|---|---|---|---|
| I | 13575870 | J-35616-64B (LT BU) | J-38125-12A | SNAC3-A021T-M0.64 | Delphi 20 | J | J |
| II | 13575871 | J-35616-35 (VT) | J-38125-12A | SNAC-A061T-M2.8 | Delphi 20 | C | A |
| III | 13575871 | J-35616-35 (VT) | J-38125-12A | SNAC-A061T-M2.8 | Delphi 20 | E | A |
| IV | 13579954 | J-35616-64B (LT BU) | J-38125-12A | Not Available | Not Available | Not Available | Not Available |
| Pin | Size | Color | Circuit | Function | Terminal Type ID | Option |
|---|---|---|---|---|---|---|
| 1 | 0.5 | RD/WH | 2740 | Battery Positive Voltage | III | - |
| 2 | 0.75 | BK | 1650 | Ground | III | - |
| 3 | 0.5 | RD | 2940 | Battery Positive Voltage | III | - |
| 4 | 1.5 | RD/VT | 4040 | Battery Positive Voltage | II | - |
| 5 - 6 | - | - | - | Not Occupied | - | - |
| 7 | 0.5 | D-BU/YE | 5361 | Brake Apply Sensor Signal | I | - |
| 8 | 0.35 | YE | 6817 | LED Backlight Dimming Control | I | - |
| 9 | 0.35 | YE/GY | 44 | Instrument Panel Lamp Dimmer Switch Signal | I | - |
| 10 | 0.13 | WH | 278 | Ambient Light Sensor Signal | IV | - |
| 11 | 0.35 | VT/YE | 5526 | Tap Up/Tap Down Switch Signal | I | - |
| 12 | 0.35 | YE/D-BU | 1505 | Passenger Heated Seat Switch Signal | I | - |
| 13 | 0.5 | WH | 5359 | Brake Apply Sensor Control | I | - |
| 14 | 0.13 | D-BU | 1788 | Traction Control Switch Signal (1) | IV | - |
| 15 | 0.35 | L-GN | 4512 | Wireless Charging System Charge Indicator Control | I | - |
| 16 | 0.35 | GY | 3273 | Remote Function Actuator Low Reference | I | - |
| 17 | 0.13 | D-BU | 5723 | Ignition Mode Switch Mode Voltage | IV | - |
| 18 | 0.35 | VT/D-BU | 6189 | Lift Glass/Rear Compartment Lid Interior Release Signal | I | - |
| 19 - 20 | - | - | - | Not Occupied | - | - |
| 21 | 0.35 | L-GN/GY | 6135 | Local Interconnect Network Serial Data Bus 4 | I | - |
| 22 | 0.35 | L-GN | 5060 | Low Speed GMLAN Serial Data | I | - |
| 23 | 0.5 | WH | 2501 | High Speed GMLAN Serial Data (-) (1) | I | - |
| 24 | 0.5 | D-BU | 2500 | High Speed GMLAN Serial Data (+) (1) | I | - |
| 25 | 0.35 | GY/YE | 3272 | Remote Function Actuator Control | I | - |
| 26 | 0.35 | L-GN/WH | 111 | Hazard Switch Signal | I | - |
| 27 | 0.35 | YE/L-GN | 3274 | Remote Function Actuator Transmit Signal | I | - |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.