SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2016CORVETTE Z06, 2D COUPE, STANDARD TRANSREPAIR AND DIAGNOSIS (SINGLE PAGE)ENGINE MECHANICALSTARTERBATTERY, CHARGING SYSTEM AND STARTING SYSTEMREPAIR INSTRUCTIONSBATTERY POSITIVE CABLE REPLACEMENT (LT1, LT4)REMOVAL PROCEDURE
2016 Chevrolet Corvette Z06, 2D Coupe, Standard Trans

Removal Procedure

2016 Chevrolet Corvette Z06, 2D Coupe, Standard TransSECTION Removal Procedure
  1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .
  2. Remove the quarter lower rear trim. Refer to Quarter Lower Rear Trim Panel Replacement .
  3. Remove the rear compartment side trim. Refer to Rear Compartment Side Trim Replacement - Right Side (Coupe) and Rear Compartment Side Trim Replacement - Right Side (Convertible) .
  4. Remove the passenger seat. Refer to Driver or Passenger Seat Removal and Installation .
  5. Remove the body lock pillar trim panel. Refer to Body Lock Pillar Trim Panel Replacement (Coupe) and Body Lock Pillar Trim Panel Replacement (Convertible) .
  6. Remove the front side door sill garnish molding. Refer to Front Side Door Sill Garnish Molding Replacement .
  7. Remove the body control module (BCM) bracket fasteners. Refer to Body Control Module Bracket Replacement .
  8. Remove the radiator surge tank. Refer to Radiator Surge Tank Replacement .
  9. Remove the battery positive cable cover (3) and remove the battery positive cable fastener (2), from the rear cargo fuse block.
    Fig 1: Battery Positive Cable Cover
    GM3355523Courtesy of GENERAL MOTORS COMPANY
  10. Detach the battery positive cable (1) from the rear cargo fuse block.
  11. Remove the battery positive cable retainers (1) and remove the battery positive cable (2) from behind the frame supports.
    Fig 2: Battery Positive Cable Retainers
    GM3355506Courtesy of GENERAL MOTORS COMPANY
  12. Remove the battery positive cable retainers (1) and move the battery positive cable (2) into the passenger compartment.
    Fig 3: Battery Positive Cable Retainers And Battery Positive Cable
    GM3355501Courtesy of GENERAL MOTORS COMPANY
  13. Remove the battery positive retainers (1) along the passenger door sill plate.
    Fig 4: Battery Positive Retainers
    GM3355498Courtesy of GENERAL MOTORS COMPANY
  14. Detach the battery positive cable retainer (2) and remove the battery positive cable grommet (1), from the battery positive cable.
    Fig 5: Battery Positive Cable Retainer And Battery Positive Cable Grommet
    GM3355494Courtesy of GENERAL MOTORS COMPANY
  15. Remove the accessory wiring junction block cover (1) and remove the battery positive cable fastener (2).
    Fig 6: Accessory Wiring Junction Block Cover
    GM3355489Courtesy of GENERAL MOTORS COMPANY
  16. Detach the battery positive cable retainer (4), from the floor panel extension and slide the battery positive cable through the dash panel plenum.
  17. Remove the battery positive cable from the passenger compartment.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.