SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2015SILVERADO 1500 HIGH COUNTRY, 5.3L ENG VIN C, RWD, GASREPAIR AND DIAGNOSISEXTERNAL PAGESDIFFERENT CARSECTION 1010 (ANTI-LOCK BRAKE SYSTEM, TRACTION CONTROL SYSTEM & STABILITY CONTROL SYSTEM)REPAIR INSTRUCTIONSREAR WHEEL SPEED SENSOR RING REPLACEMENTINSTALLATION PROCEDURE
2015 Chevrolet Silverado 1500 High Country, 5.3L Eng VIN C, RWD, Gas

Installation Procedure

2015 Chevrolet Silverado 1500 High Country, 5.3L Eng VIN C, RWD, GasSECTION Installation Procedure
WARNING: This page is about a different car, the 2008 GMC Sierra, 2008 GMC Cab & Chassis Sierra, 2008 Chevrolet Silverado, and 2008 Chevrolet Cab & Chassis Silverado. However, it is still accessible from the selected car via links, so may be relevant.
    Fig 1: Installing Wheel Speed Sensor Ring Using J 45860 & J 8092
    GM885621Courtesy of GENERAL MOTORS CORP.
  1. Install the wheel speed sensor ring using the J 45860  (1) and the J 8092  (2). See Special Tools .
  2. Drive the wheel speed sensor ring into the axle housing until the tool bottoms against the tube.
    3. Fig 2: Installing Axle Shaft Bearing Using J 23690 Or J 29709 & J 8092
    GM695758Courtesy of GENERAL MOTORS CORP.
  3. Install the axle shaft bearing using the J 23690  (1) and the J 8092  (2). See Special Tools .
  4. Drive the axle shaft bearing into the axle housing until the tool bottoms against the tube.
    5. Fig 3: Installing Axle Shaft Seal Using J 21128
    GM885624Courtesy of GENERAL MOTORS CORP.
  5. Install the axle shaft seal using the J 21128  . See Special Tools .
  6. Drive the tool into the bore until the axle shaft seal bottoms flush with the tube.
  7. Install the axle shaft. Refer to Rear Axle Shaft Replacement (8.6 Inch Axle w/Drum Brake w/VSES) or Rear Axle Shaft Replacement (8.6 Inch Axle w/Drum Brakes w/o VSES) or Rear Axle Shaft Replacement (8.6, 9.5 Inch Axles w/VSES) .
  8. Install the rear axle housing cover. Refer to Rear Axle Housing Cover and Gasket Replacement .
  9. Install the rear wheel speed sensor. Refer to Rear Wheel Speed Sensor Replacement .
  10. Install the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation .
  11. Fill the rear axle. Refer to Rear Axle Lubricant Replacement (8.6 Inch Axle) or Rear Axle Lubricant Replacement (9.5 Inch LD Axle) or Rear Axle Lubricant Replacement (10.5 Inch Axle) .
  12. Lower the vehicle.
RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready ToolsFree Quote CheckQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.