Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2015SILVERADO 1500 HIGH COUNTRY, 5.3L ENG VIN C, RWD, GASREPAIR AND DIAGNOSIS (SINGLE PAGE)QUICK LOOKUPSWIRING DIAGRAMSWIRING SYSTEMS AND POWER MANAGEMENT - COMPONENT CONNECTOR END VIEWS - F113P TO K20 X2 LMLCOMPONENT CONNECTOR END VIEWSK9 BODY CONTROL MODULE X4
2015 Chevrolet Silverado 1500 High Country, 5.3L Eng VIN C, RWD, Gas
K9 Body Control Module X4
2015 Chevrolet Silverado 1500 High Country, 5.3L Eng VIN C, RWD, GasSECTION K9 Body Control Module X4
Connector Part Information
|
Terminal Part Information
| Terminal Type ID | Terminated Lead | Diagnostic Test Probe | Terminal Removal Tool | Service Terminal | Tray | Core Crimp | Insulation Crimp |
|---|---|---|---|---|---|---|---|
| I | 13575871 | J-35616-35 (VT) | J-38125-12A | Not Required | Not Required | Not Required | Not Required |
| I | 13575871 | J-35616-35 (VT) | J-38125-12A | Not Required | Not Required | Not Required | Not Required |
| II | 13582297 | J-35616-64B (LT BU) | J-38125-22 | Not Required | Not Required | Not Required | Not Required |
| II | 13582297 | J-35616-64B (LT BU) | J-38125-22 | Not Required | Not Required | Not Required | Not Required |
| II | 13582297 | J-35616-64B (LT BU) | J-38125-22 | Not Required | Not Required | Not Required | Not Required |
| III | 13582298 | J-35616-64B (LT BU) | J-38125-22 | Not Required | Not Required | Not Required | Not Required |
| Pin | Size | Color | Circuit | Function | Terminal Type ID | Option |
|---|---|---|---|---|---|---|
| 1 | 0.75 | YE | 712 | Left Headlamp Low Beam Control | I | - |
| 2 | 0.75 | YE | 312 | Right Headlamp Low Beam Control | I | - |
| 3 | 0.75 0.75 |
L-GN/VT - |
1315 1315 |
Right Front Turn Signal Lamp Control | I | - - |
| 4 | 0.5 0.5 |
BN BN/L-GN |
19 19 |
Right Rear Stop/Turn Lamp Control | I | - - |
| 5 - 6 | - | - | - | Not Occupied | - | - |
| 7 | 0.75 0.75 |
GY/D-BU GY |
7538 7538 |
Left Front DRL Control | II III |
- - |
| 8 - 10 | - | - | - | Not Occupied | - | - |
| 11 | 0.5 | VT/WH | 5065 | Stop Lamp Relay Coil Control | II | - |
| 12 | 0.35 | GY/VT | 755 | RAP Relay Coil Control | II | - |
| 13 | 0.5 0.5 |
L-GN/YE - |
6846 6846 |
Rear License Lamp Control | II | - - |
| 14 | 0.35 | BN/GY | 2268 | Windshield Washer Relay Control | II | - |
| 15 | 0.35 0.35 |
- L-GN/VT |
5199 5199 |
Run/Crank Relay Coil Control | II | - - |
| 16 | 0.35 | GY | 91 | Windshield Wiper Motor Relay Coil Control | II | - |
| 17 | 0.5 0.5 |
BN/L-GN BN |
196 196 |
Windshield Wiper Motor Park Switch Signal | II | - - |
| 18 | 0.35 | WH/YE | 5075 | Current Sensor Signal | II | - |
| 19 | 0.35 0.35 |
- D-BU/YE |
6844 6844 |
ABS/TCS Hill Descent Control Switch Signal | II | - - |
| 20 | 0.75 0.75 |
RD/YE RD/YE |
2340 2340 |
Battery Positive Voltage | III II |
- - |
| 21 | 0.35 0.35 |
D-BU/VT - |
5076 5076 |
Current Sensor Control | II | - - |
| 22 | 0.35 | VT/YE | 5985 | Accessory Wakeup Serial Data | II | - |
| 23 | 0.5 0.5 |
WH/D-BU WH |
5986 5986 |
Serial Data Communication Enable | II | - - |
| 24 | 0.5 0.5 |
BN/L-GN BN |
109 109 |
Hood Ajar Switch Signal | II | - - |
| 25 | 0.5 0.5 |
L-GN/YE - |
2081 2081 |
Exhaust Brake Switch Control | II | - - |
| 26 | 0.75 0.75 |
BK/WH BK/WH |
451 451 |
Signal Ground | III II |
- - |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.