Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2015EXPRESS 2500 BASE, VAN CARGO EXTENDED, 6.0L ENG VIN BREPAIR AND DIAGNOSISSTEERINGSTEERING WHEEL AND STEERING COLUMNCOMPONENT LOCATORSTEERING COLUMN DISASSEMBLED VIEW (TILT COLUMN)TILT COLUMN
2015 Chevrolet Express 2500 Base, Van Cargo Extended, 6.0L Eng VIN B
Tilt Column
2015 Chevrolet Express 2500 Base, Van Cargo Extended, 6.0L Eng VIN BSECTION Tilt Column
| Callout | Component Name |
|---|---|
| 1 | Upper Trim Cover |
| 2 | Lower Trim Cover |
| 3 | Shift Lever |
| 4 | Shift Lever Screw |
| 5 | Shift Lever Seal |
| 6 | Flange Prevailing Torque Nut |
| 7 | Retaining Ring |
| 8 | Inflatable Restraint Steering Wheel Module Coil |
| 9 | Wave Washer |
| 10 | Bearing Retainer |
| 11 | Cam Orientation Plate |
| 12 | Turn Signal Cancel Cam Assembly |
| 13 | Upper Bearing Spring |
| 14 | Upper Bearing Inner Race Seat |
| 15 | Inner Race |
| 16 | Bearing Assembly |
| 17 | Switch Mounting Bracket |
| 18 | Ignition Lock Cylinder Case |
| 19 | TORX Head Screws |
| 20 | Coded Key Controller |
| 21 | Ignition Switch Assembly |
| 22 | Steering Column Tilt Head Assembly |
| 23 | Tilt Bumper |
| 24 | Bearing Assembly |
| 25 | Inner Race |
| 26 | TORX Head Screw |
| 27 | Linear Shift Assembly |
| 28 | Electrical Actuator |
| 29 | Race and Upper Shaft Assembly |
| 30 | Centering Sphere |
| 31 | Lower Steering Shaft Assembly |
| 32 | Anti-rotation Pin |
| 33 | Shoe Pivot Pin |
| 34 | Pan Head Tapping Screw |
| 35 | Turn Signal and Multifunction Switch Assembly |
| 36 | Steering Wheel Lock Shoe |
| 37 | Shoe Release Lever Assembly |
| 38 | Tilt Knob |
| 39 | Compression Spring |
| 40 | Spring Guide |
| 41 | Tilt Spring |
| 42 | Steering Wheel Lock Support Shoe |
| 43 | Pivot Pin |
| 44 | Spring Pin |
| 45 | Steering Column Jacket Assembly |
| 46 | Wire Harness Assembly |
| 47 | Adapter and Bearing Assembly |
| 48 | Bearing Assembly |
| 49 | Hex Head Nut |
| 50 | Pinch Bolt |
| 51 | Intermediate Shaft |
| 52 | Inner Boot Seal |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.