Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2013SILVERADO 1500 4WD V8-5.3LREPAIR AND DIAGNOSISHEATING AND AIR CONDITIONINGCABIN VENTILATION GRILLESERVICE AND REPAIR
2013 Chevrolet Silverado 1500 4WD V8-5.3L
Cabin Ventilation Grille: Service and Repair
2013 Chevrolet Silverado 1500 4WD V8-5.3LSECTION Service and Repair
Pressure Relief Valve Replacement
Removal Procedure
1. Remove the rear window lower garnish molding. Refer to Rear Window Lower Garnish Molding Replacement (Regular Cab) Rear Window Lower Garnish Molding Replacement (Regular Cab)Rear Window Lower Garnish Molding Replacement (Ext Cab/Crew Cab w/A48) Rear Window Lower Garnish Molding Replacement (Ext Cab/Crew Cab w/A48)Rear Window Lower Garnish Molding Replacement (Ext Cab/Crew Cab w/o A48) Rear Window Lower Garnish Molding Replacement (Ext Cab/Crew Cab w/o A48)
2. Remove the body lock pillar trim. Refer to Body Lock Pillar Trim Replacement (Extended Cab) Body Lock Pillar Trim Replacement (Extended Cab)Body Lock Pillar Trim Replacement (Crew Cab) Body Lock Pillar Trim Replacement (Crew Cab)Body Lock Pillar Trim Replacement (Regular Cab) Body Lock Pillar Trim Replacement (Regular Cab)
3. Pull back carpeting on the rear wall of the cab exposing the pressure relief valve.
4. Press on the retaining tab on the top downward to release the valve from the cab back panel.
5. Remove the pressure relief valve from the vehicle.
Installation Procedure
1. Align the pressure relief valve into the opening of the rear cab.
2. Press the pressure relief valve into the cab back panel until the locking tabs are fully seated.
3. Realign carpeting on the rear wall of the cab to lay flat.
4. Install the body lock pillar trim. Refer to Body Lock Pillar Trim Replacement (Extended Cab) Body Lock Pillar Trim Replacement (Extended Cab)Body Lock Pillar Trim Replacement (Crew Cab) Body Lock Pillar Trim Replacement (Crew Cab)Body Lock Pillar Trim Replacement (Regular Cab) Body Lock Pillar Trim Replacement (Regular Cab)
5. Install the rear window lower garnish molding. Refer to Rear Window Lower Garnish Molding Replacement (Regular Cab) Rear Window Lower Garnish Molding Replacement (Regular Cab)Rear Window Lower Garnish Molding Replacement (Ext Cab/Crew Cab w/A48) Rear Window Lower Garnish Molding Replacement (Ext Cab/Crew Cab w/A48)Rear Window Lower Garnish Molding Replacement (Ext Cab/Crew Cab w/o A48) Rear Window Lower Garnish Molding Replacement (Ext Cab/Crew Cab w/o A48)
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.