Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2013CRUZE LS, 1.8L ENG VIN H, STANDARD TRANSREPAIR AND DIAGNOSISGENERAL INFORMATIONOEM GENERAL INFORMATIONVEHICLE DIAGNOSTIC INFORMATIONSPECIFICATIONSMULTIMEDIA PLAYER INTERFACE MODULE SCAN TOOL INFORMATION
2013 Chevrolet Cruze LS, 1.8L Eng VIN H, Standard Trans
Multimedia Player Interface Module Scan Tool Information
2013 Chevrolet Cruze LS, 1.8L Eng VIN H, Standard TransSECTION Multimedia Player Interface Module Scan Tool Information
Multimedia Player Interface Module Scan Tool Data Parameters
| Parameter | Expected Value | Definition |
|---|---|---|
| Operating Conditions: Ignition ON/Engine OFF/Radio ON | ||
| GM Part Number | Varies | The scan tool displays the part number. |
| Calibration Part Number 1 | Varies | The scan tool displays the primary software part number. |
| Calibration Part Number 2 | Varies | The scan tool displays the primary calibration part number |
| Battery Voltage | Varies | The scan tool displays volts. This is the voltage input supplied to the Multimedia Player Interface Module. |
| USB Device Detection | Inactive | The scan tool displays Active or Inactive. Being active indicates a USB device is connected. |
| Aux IN Detection | Inactive | The scan tool displays Active or Inactive. Sensing& Status. This parameter displays active when a device present on AUX In (ministereo plug). |
| USB Overcurrent Protection | Inactive | The scan tool displays Active or Inactive. USB over current detection indicates a USB device is drawing too much current and the USB functionality of the device is turned OFF. |
| Bluetooth Device Detection | Inactive | The scan tool displays Active or Inactive. Active indicates a Bluetooth device connected. |
| Mute Status | Mute OFF | The scan tool displays Mute OFF or Mute ON. This parameter displays the status of the mute. |
| Audio Source Status | Internal | The scan tool displays Internal Source, AUX or Bluetooth.This parameter displays the source of the audio. |
| USB Power Status | OFF | The scan tool displays OFF or ON. This is the status of the USB power. |
| Connected Device Type 1 | None | The scan tool displays None, USB Mass Storage Device, USB Media Transfer Protocol Device, Media Player- iPod, Bluetooth, AUX, Media Player- Zune, or Device Inserted But Not Supported. This parameter displays the type of auxiliary input source connected. |
| Connected Device Type 2 | None | The scan tool displays None, USB Mass Storage Device, USB Media Transfer Protocol Device, Media Player- iPod, Bluetooth, AUX, Media Player- Zune, or Device Inserted But Not Supported. This parameter displays the type of auxiliary input source connected. |
| Connected Device Type 3 | None | The scan tool displays None, USB Mass Storage Device, USB Media Transfer Protocol Device, Media Player- iPod, Bluetooth, AUX, Media Player- Zune, or Device Inserted But Not Supported. This parameter displays the type of auxiliary input source connected. |
| Connected Device Type 4 | None | The scan tool displays None, USB Mass Storage Device, USB Media Transfer Protocol Device, Media Player- iPod, Bluetooth, AUX, Media Player- Zune, or Device Inserted But Not Supported. This parameter displays the type of auxiliary input source connected. |
| Bluetooth Signal Strength | DB | The scan tool displays the signal strength of the Bluetooth connection. |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.