Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSCHEVROLET2013CRUZE LS, 1.8L ENG VIN H, STANDARD TRANSREPAIR AND DIAGNOSISGENERAL INFORMATIONOEM GENERAL INFORMATIONVEHICLE DIAGNOSTIC INFORMATIONSPECIFICATIONSFUEL PUMP FLOW CONTROL MODULE SCAN TOOL INFORMATION
2013 Chevrolet Cruze LS, 1.8L Eng VIN H, Standard Trans
Fuel Pump Flow Control Module Scan Tool Information
2013 Chevrolet Cruze LS, 1.8L Eng VIN H, Standard TransSECTION Fuel Pump Flow Control Module Scan Tool Information
Fuel Pump Flow Control Module Scan Tool Data Parameters
| Parameter | System State | Expected Value | Description |
|---|---|---|---|
| Operating Conditions: Ignition ON/Engine Idling at Normal Operating Temperature / Vehicle is in Park or Neutral | |||
| Desired Fuel Pressure | - | 306.8 kPa (44.5 psi) | This displays kPa (psi). This is the desired fuel pressure. |
| Fuel Pump Command | - | On | The scan tool displays On or Off. This is the current state of the fuel pump command. |
| Fuel Pump Signal Command | - | Varies | This displays %. This is the commanded fuel pump signal measured in percentage. |
| Fuel Pressure Sensor | - | 296.4-310.3 kPa (43-45 psi) | This displays kPa (psi). This is the current pressure at the fuel pressure sensor. |
| Fuel Pressure Sensor | - | 4.90-5.01 Volts | This displays Volts. This is the fuel pressure sensor voltage. |
| Ignition 1 Signal | - | Varies | This displays Volts. This is the current ignition 1 signal. |
| LT Fuel Pump Trim | - | Varies | This displays a numeric value. This is the long term (LT) fuel pump trim. |
| ST Fuel Pump Trim | - | Varies | This displays a numeric value. This is the short term (ST) fuel pump trim. |
Fuel Pump Flow Control Module Scan Tool Output Controls
| Output Control | Description |
|---|---|
| Fuel Pressure Control | This output control is used to control the fuel pressure. |
| Fuel Pump | This output control is used to command the fuel pump ON and OFF. |
| Fuel Pump Trim Reset | This output control is used to reset the fuel pump trim. |
Active Grille Air Shutter Scan Tool Data Parameters (If Equipped)
| Parameter | System State | Expected Value | Description |
|---|---|---|---|
| Operating Conditions: Ignition ON/Engine Idling at Normal Operating Temperature / Vehicle is in Park or Neutral | |||
| Active Grille Air Shutter Position Command | - | Varies | This displays %. This is the commanded active grille air shutter position. |
| Active Grille Air Shutter Position | - | Varies | This displays %. This is the actual active grille air shutter position. |
| Cold Temperature Mode | - | On / Off | The scan tool displays On or Off. This is the current state of the Cold Temperature Mode. |
| Ambient Air Temperature | - | Varies | The scan tool displays °C (°F). This is the current ambient air temperature. |
Active Grille Air Shutter Scan Tool Output Controls (If Equipped)
| Output Control | Description |
|---|---|
| Active Grille Air Shutter Actuator | This output control is used to perform the Active Grille Air Shutter Actuator test. It is used to cycle the active grille air shutter open and closed. The test result will display pass or fail based on the ability of the louvers to cycle open and closed. |
Exhaust Flow Control Valve Scan Tool Data Parameters (If Equipped)
| Parameter | System State | Expected Value | Description |
|---|---|---|---|
| Operating Conditions: Ignition ON/Engine Idling at Normal Operating Temperature / Vehicle is in Park or Neutral | |||
| Exhaust Flow Control Valve Command | - | Open/Closed | Exhaust Flow Valve Commanded State |
| Exhaust Flow Control Valve Command | - | % | Exhaust Flow Valve Commanded Duty Cycle (0%-100%) |
| Exhaust Flow Control Valve Performance Mode | - | Active/Inactive | Exhaust Flow Valve Control Status |
| Exhaust Flow Control Valve Rumble Mode | - | Active/Inactive | Exhaust Flow Valve Control Status |
| Exhaust Flow Control Valve | - | Active/Inactive | Exhaust Flow Valve Control Status |
Exhaust Flow Control Valve Scan Tool Output Controls (If Equipped)
| Output Control | Description |
|---|---|
| Exhaust Flow Control Valve Command | This output control is used to cycle the exhaust flow control valve open and closed. |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.